Avedare,
Unfortunately, I haven’t been doing this book for a long time. In this situation, as far as I can judge, the main thing is to make it determined on the PC. For all devices that have flashROM (mp3 players, readers, tablets), there is a universal method of switching to maskrom mode - closing the io0-io1 flash pins before switching on. Those. in your case:
- open
- determine the type of flash
- find on the Internet, which "legs" to close
- connect to PC
- close the contacts with a needle
- turn on the power
After this reader must decide
- remove the needle
- flash

I do not know, maybe I should create a new topic. Turned up recently on the occasion of the factory firmware on the readerAssistant AE-601, I searched for it for quite a long time, maybe someone else will need it.

Post has been editedllitr - 29.11.14, 22:47

llitr
Assistant AE-601

I finally can not understand how to flash a book 501 4gb
Can someone write the points humanly (as easily as possible) to write how to flash assistant AE-501 (for ITEMS!) And where to get an adequate firmware, thanks in advance.

Post has been editedjstarks - 11.02.15, 18:23

Here in the cache found withoff site, the admin wrote how to reflash so as not to bother.

1. Write to microSD in the init folder the files system.upg.md5 and system.upg.
2.Insert the USB flash drive into the device's card reader
3. In the device, go to the "settings" and run the "update".
4. In the menu that appears, select System.
5. A red screen appears, wait until the device reboots.

It is not clear under paragraph 1, only system.upg.md5 and system.upg or all files that should be archived with the firmware should be uploaded to the folder.
Only here the firmware on the site is no longer. Who has it preserved on the computer, please post it, I understand this is the latest firmwareupdate1.rar - in the archive system.upg from 01/21/2011, the remaining parts of the firmware are rather old Attached file update1.rar (90,44 РњР‘)

Post has been editedjstarks - 11.02.15, 21:53

Damn zasrat already topic, does not allow to edit the message that would add a question, sor. Well, such a question, I lost the DC charging wire, and about 3-4 months I charged through the mini USB cable (in the book and then in the power supply and in the outlet), after which the port on the email burned. The book, now in the SC, they rewrote a new port (mini usb), maybe this is due to the fact that you need to charge the input through the DC and not through the mini USB, tell me plz.

Good day
there was such a question: there is a touch-sensitive e-book Lexand LE-116 on a JZ4755 processor and electronic ink
Will the firmware from this topic work on it?
They as I understand are presented for books with tft screen?

ckin,
Naturally will not work.

Lexand LE-116

I have a LEXAND LT-105 firmware:



Is it possible to reflash to some kindred firmware, where it is possible to adjust the brightness of the backlight during the reading and the bookmarks were loaded exactly on the page where this tab was made? Bookmarks never open on the page where they were made, most often you have to scroll a couple of times to find the moment where the bookmark was made (this is very inconvenient and annoying).

Good night all.
On the hands there is assistant AE-50104.
Everywhere they write that this device supports the avi format.
I decided to try, downloaded a file of 14 megabytes. poured on the device.
But the file is not displayed anywhere, maybe I am doing something wrong.
Maybe you need to place the file in some specific folder.
Can someone tell me what could be the problem

Gives the message:

An error occurred while trying to install these drivers.
Third-party INF does not contain signature information.

What to do?

Topmember
Disable signature verification in Windows.

If the AE-501 book is not flashed, the book does not start a black screen, you must run each file separately, bootoader, then kernel, etc. But not the system file right away.

I will correct the author a little higher

I found it in the cache from the off site site, the admin wrote how to reflash to not bother.

1. Write to microSD in the init folder (if there is no folder, then create it with that name) files system.upg.md5, kernel.upg, system.upg.
2.Insert the USB flash drive into the device's card reader
3. In the device, go to the "settings" and run the "update".
4. In the menu that appears, select the System and if it did not help after the system has been flashed, select the Kernel.
5. A red screen appears, wait until the device reboots.

It helped me exactly the firmware rewrite! The device began to work normally, you just have to change the language from Chinese to yours.


Assistant AE-501.rar(84.11 MB)


Post has been editedAtti1a - 23.05.18, 10:05

It turns out that the latest version is the end of January 2011 ...
Fresh nothing?