For beginners, you can update the firmware via a flash drive. To do this, download the firmware and the system.upg file on the flash drive of the device in the init directory, if not, create one. Then, in the device, select the software update system. We wait. Voila

Outcast-d.o.b,
You can backup, and lay out) can come to my assistant)

So here) I filled in the Assistant AE-501 firmware from LASER from 09/10/2010 (which is in the cap). the book started and started working) did not calm down, and gave a request for firmware from LEXAND LT-105. I got a link ([email protected]). I installed it) I just chose the firmware for the 4 GB booklet. The flight is normal. in the menu there is a Ukrainian language. 700 MB video opens normally (as for this particular reader). here is the link to the firmware fromLEXAND LT-105

remind (if relevant will be) in a week another.
The book is currently at Smolensk, where the firmware has absolutely nothing to shoot.
It is very interesting to know what you say about this firmware.

Post has been editedOutcast-d.o.b - 20.06.13, 00:25

Outcast-d.o.b,
Most likely I have already downloaded this) is good) is faster and less tupit than from the assistant asking. I'm sitting on it now) but anyway, if the opportunity arises, throw off the firmware)

Is it possible to pour Android on this device?

onunimuz,
Such precedents are unknown. What for?

Post has been editedRedscorpio - 11.10.13, 06:03

Hello! Guys tell me how to flash this device? Boot into USB Boot Device, now it does not turn on after reset, I do not know what to do. Probably something pressed in the USB_Boot folder, did the program itself write something wrong (((

Posted on 10/13/2013, 23:38:

USB Boot Device is now the first option is not loaded, loaded by option number 3.

here is the log:
>nprogb 8388608 root.upg 0 0 -n
start block 16 / start page 2048 / start byte 8388608
Can not open file!
Checking state of device No.0: 4750 Booted
Now configure device No.0:

ID of flash No.0 of device No.0:
Vendor ID: 0xad
Product ID: 0xd5
Chip ID: 0x94
Page ID: 0x25
Plane ID: 0x44

H27UAG8T2A detected

Now check whether all configure args valid:
Current device information: CPU is Jz4750
Crystal work at 24MHz, the CCLK up to 336MHz and PMH_CLK up to 112MHz
Total SDRAM size is 16 MB, work in 4 bank and 16 bit mode
Nand total size 2 GB, 4096 blocks, 128 pages per block
page size 4096, ECC offset 16, ECC block size 256
bad block page 126, pos 0
2nd bad block page 127, pos 0
oob size 224
use 1 plane mode
device No.0 configure success!
Erasing flash No.0 device No.0 ... Finish!
Operation end position: 4096
There are marked bad blocks: 0

Understood, flashed, everything works!))) But the SD card does not see, before that, the charging connector was repaired when it was done, the hike was damaged.

People, skinte somebody backup full firmware or full firmware m-book mini. All Internet rummaged - no where there is no (((

Maybe you better refer to the profile topic.M-Book mini

I wrote there too. But I need this firmware to raise the AE-501.

It is strange that you "raise" AE-501 "non-native" firmware

Upgrade_M-Book_Mini_05-04-2012.rar
Upgrade_M-Book_Mini_02-02-2011_bez_chehla.rar
Upgrade_M-Book_Mini_24-03-2011_bez_chehla.rar
Upgrade_M-Book_Mini_24-03-2011_chehol.rar

Thank you very much! I swing, the first should approach.
Nothing strange, I needed full firmware, and all the firmware from Assistant have only system.upg

No, it's all the same strange. All 4 firmware onmanufacturer's website(update1, update2, update3, update4) contain all four parts of the firmware.

(((and I shook from here, I thought that this was official.

Now onmanufacturer's websiteThere is no official firmware, only:
- update1.rar - in the system.upg archive from 01/21/2011, the other parts of the firmware are rather old update1.rar (90.44 MB)
- update2.rar - in the archive all parts of the firmware are quite old update2.rar (100.48 MB)
- update3.rar - in the archive firmware Energy 2GB (W851), all parts of the firmware are quite old update3.rar (98.74 MB)
- update4.rar - in the archive firmware Tiwell 4GB (W851), all parts of the firmware are quite old update4.rar (88.26 MB)

Just in case (for example, the disappearance of a page from the manufacturer’s website, as happened with the M-Book mini) I fix all these firmware here.

Who knows, in any Assistants AE-501 firmware, can I change the background color (and letter color) of the reading room, or is there only a white background everywhere?

RedScorpio, After launching the bat nand_eraseall.bat by inertia, the book was no longer defined at all. How can I return what I erased, do not tell me?