OPTION FIRMWARE QTEK 9100 (G4) not using USB
Well, the action itself, briefly tell you why without the aid of usb. It so happened that I, the happy owner of Qtek 9100, was not synchronize with a computer via usb cable, well, that's not seen BB body. Tried variants with replacement OSes themselves computers, usb laces, XP on the body, no options - the body to use a usb port for charging current. I must say that the synchronization was bang via bluetooth and on any computers, OSes, and asset Cinco.
All this business principle does not bother me as long as I did not want to flash the body WM 6 as a white man. Trouble started here .... which is not without the help of the participants of this forum successfully resolved: rolleyes: ...
Just specify that option exclusively for owners Qtek 9100 G4 !!!You can find out what G you have by SPL in BootLoaders
DOC G3 -
IPL x.xx.0000
SPL x.xx.0000
or
IPL x.xx
SPL x.xx
DOC G4 -
IPL x.xx.0001
SPL x.xx.0001В© frog
So, to start on the BB with which we sew, OS Windows Vista Ultimate, a program to synchronize with the body - Windows Mobile Device Center (for Vista sinc asset usually does not work).
1. For the firmware, we need to:
BB, the body working synchronization with BB via bluetooth package Emerald-2.5.1 RUS firmware desire ..;)
2. Downloading package Emerald-2.5.1 firmware here:
http://depositfiles.com/ru/files/wuwvjz9lyhttp://rapidshare.com/files/165967442/Emerald251.ziphttp://ifolder.ru/9094845(I personally took the first link)
3. Unpack the archive to a folder.
4. From this point carefully !! Charges up to stop his body (in principle I have to stitch up to 50% but advised people in the know better not to risk), you can also take out the sd card (if available) and sim-ku, I should say I did not do this. If you do not want to lose important data make back up, I did not vsledstvii that lost contact and some important documents: D
5. Sync body with BB (via bluetooth esssno because we decided that the usb port is not working with us: D)
6. There is one detail in the firmware package that we downloaded, in principle, all collected and automated, BUT !! I went a little bit the other way because
the method specified in the manual firmware package on my body did not pass !!! 7. Go to the folder with the firmware, Emerald-2.5.1 \ ShellTool \ cab
8. In the folder there are two cab file Cert_SPCS.cab EnableRapi.cab and copy them into
MAINbody memory,
SAME WAYset at a time
9. After the installation files are waiting for 3-4 minutes and restart the body.
10. Again, set up the synchronization with the BS
11. Turning off on a computer antivirus software, firewalls, a firewall, etc. (Personally, I have worked during the firmware Antivir and firewall but it is better not to risk it), turn off all running programs and applications.
12. Go to the folder with the firmware Emerald-2.5.1 \ BaseROM there nk.nbf file copy it to a folder ShellTool
13. In the folder there is a file ShellTool ShellTool.exe - run it
14. Click Get ROM info. You'll see information about the contents of the ROM
15. Click Extract OS and wait until it ejects filling ROM
should get out:
Extracting OS ...
Please wait ...
Done!
16. Press the Flash OS followingManufacture you will see:
********************
!!! Please make sure that: !!!
!!! You enabled the RAPI (setuped EnableRAPI.cab and rebooted)
!!! You connected your Wizard to the PC with USB ActiveSync connection
*** Please, dont touch your device or PC while flashing ***
*** Because you may abort this operation !!! Dont do that !!! ***
*** You will get the message when your device will be flashed !!! ***
********************
*** Press OK to start ***
********************
17. Do not be frightened about You connected your Wizard to the PC with USB ActiveSync connection
Click OK
18. After clicking "OK" ShellTool starts flashing device. Will come out about this:
---- !!! This process takes more tnan 15 minutes !!! ----
[10: 56: 43,71] Write ROM 80040000-OS.nb Start
Do not disconnect the Wizard during the process
********************
Principle in the original instruction, where I took it, it is written that you will not see any signs of body sewing, but my first body about a minute on the screen began to swirl arrows with BB device synchronization
Thus, in contrast perhaps to the embodiment of the firmware via usb the process I took no 15 and 25 minutes.
IMPORTANT!!! I admit, after waiting about 20 minutes, I lost hope and was about to interrupt the process, do not do it !!! WE WAIT!!19. A sign of the end of the process can be considered as the inscription:
(Time) ROM 80040000-OS.nb End "
*** PLEASE !!! MAKE HARD RESET ***
20. Make XP body (making sure I did for worrying, soft reset, in principle nothing terrible has happened, the Windows boot up but fell down a lot of mistakes, so do not risk and immediately do a hard reset)
The body is slightly longer boot after boot start downloading add-ons and restart the body itself. Do not touch anything !!
21. Principle all: yes2: subject to a manual action on mine you have to be a happy user Emerald-2.5.1 WM 6.1 RUS: thank_you:
In Pictures body piercing method using shellTool can be found here:
http://forum.ladoshki.com/viewtopic.php?t=29592PLEASE NOTE THAT WE NEED OPTION FOR VEHICLES G4 !!!!Good luck to everyone and thank you!