Wexler Book T7005 - firmware
Software change instructions for WEXLER.BOOK T7005 (version 1.1) .doc
Backgrounds changed (c3 to 6). The process of flashing the book was normal. Everything works (like).
Faust3000 , it is not clear only: the amount of firmware decreased from 59.7 MB to 58.2 MB. Is this normal?
Faust3000 , it is not clear only: the amount of firmware decreased from 59.7 MB to 58.2 MB. Is this normal?
[email protected], 18:11
it is not clear only: the amount of firmware decreased from 59.7 MB to 58.2 MB. Is this normal?
Yes, it is normal, do not worry. The size has decreased due to the replacement of images, compare the size of the original image and the new one, the new one is likely to be larger, hence the difference.
Hello - tell me what could be the problem.
Removed the movie file from the book - its size became 0, but the file itself was visible in Windows. And his removal caused an error - even it was recommended to launch the scandisk for verification.
After that, the library could not be updated when the USB cable was disconnected (it hung up as it were when updating)
Hardly turned it off, and after that the book did not load to the end. on the screen saver "Vistula".
after that I flashed the book without formatting and with formatting - but all the same problems remained. That is, do not boot to the end - hanging on the screen saver.
it got worse - now everything else is even worse upgraded through LivSuit. USB sometimes connects but the computer sees it poorly - the disks are visible in the explorer but not readable.
Post has been editedHalifers - 10.12.15, 08:42
Removed the movie file from the book - its size became 0, but the file itself was visible in Windows. And his removal caused an error - even it was recommended to launch the scandisk for verification.
After that, the library could not be updated when the USB cable was disconnected (it hung up as it were when updating)
Hardly turned it off, and after that the book did not load to the end. on the screen saver "Vistula".
after that I flashed the book without formatting and with formatting - but all the same problems remained. That is, do not boot to the end - hanging on the screen saver.
it got worse - now everything else is even worse upgraded through LivSuit. USB sometimes connects but the computer sees it poorly - the disks are visible in the explorer but not readable.
Post has been editedHalifers - 10.12.15, 08:42
The wexler t7003b book was turned on, but it did not start further than the boot window, followed by juggling the screen and stripes.
In the device manager is not defined.
It turned out to flash wexler t7003b according to the instructions offeredlogosnv with the closure of the contacts of the memory chip.
Firmware from office. Site. The LiveSuit program did not want to flash.
I used from the official site "Program for updating software for T7001 v1.27" that came with the firmware, the driver was also there. And voila, the book earned !!!
In the device manager is not defined.
It turned out to flash wexler t7003b according to the instructions offeredlogosnv with the closure of the contacts of the memory chip.
Firmware from office. Site. The LiveSuit program did not want to flash.
I used from the official site "Program for updating software for T7001 v1.27" that came with the firmware, the driver was also there. And voila, the book earned !!!
Dear forum users, please do not kick, honestly tried to read all the information on Wexler, but unfortunately I did not find it.
There is a model T7055, I have it almost since the release of this model, but the manufacturer’s firmware has not changed, and there are enough flaws in the charging (charging indication, jumping pages with the sensor turned on ....). In a word, what firmware can be installed on this model (T7055)?
Post has been editedMalmu - 23.05.16, 17:52
There is a model T7055, I have it almost since the release of this model, but the manufacturer’s firmware has not changed, and there are enough flaws in the charging (charging indication, jumping pages with the sensor turned on ....). In a word, what firmware can be installed on this model (T7055)?
K
Despite the resemblance, the models T7005 and T7055 are completely different inside.
Firmware from T7005 to T7055 do not fit!
Firmware from T7005 to T7055 do not fit!
Post has been editedMalmu - 23.05.16, 17:52
Tried, does not work. From the setting mode, the wheel does not exit. And the driver is most likely needed ...
It seems that if the mouse will work, then only after system initialization. And if it is impossible to calibrate the touch, then either a book for parts, or put a new touch screen.
I can not flash it! It costs Windows10, with which it turned the book into a brick! Because of some kind of book, do you need to reinstall the whole operating system?
Olega40rus, Buy a device on Android with this approach to business. These devices have not been supported for a long time and the last firewood was for Win 7, but they worked on both 8 and 8.1, but already on the top ten alas .. The most acceptable option is to install a virtual machine with XP and from there to flash.
Hah! I upgraded from under the 10! Fresh LiveSuite v1.11 and the separately found and installed driver vid_1f3a_pid_efe8 bore their fruit! The book came to life! It also filled the modified firmware without problems!
Hello, I ran into an eternal reboot, I can not flash it, the software writes that there is no device.
Tell me how to reanimate
Tell me how to reanimate
©savagemessiahzine.com2005-2019. All rights reserved.
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement