[X]Assistant

[Jdroid]

HTC Wildfire S - CyanogenMod Firmware (OS 2.3, 4.x)
HTC Wildfire S, Marvel, A510e, MarvelC, A510c, HTC G13
Description | Discussion пїЅ | FAQ | Purchase пїЅ | Accessories пїЅ | Marriage and Repair пїЅ | Fludilnya пїЅ | Games пїЅ | HTC Wildfire S Firmware пїЅ | Cyanogenmod пїЅ
MIUI (OS 2.3, 4.x) пїЅ | LeWa (OS 2.3) пїЅ | CM9 ICS BY ANSATBAY (CM7) (OS 2.3) пїЅ | HTC Wildfire S Firmware (OS 4.0) пїЅ

Before asking a question, carefully readFAQand make sure the answer to your question is not there. Questions that are answered inFAQwill be ignored and regarded as offtop. It is also strongly recommended to reinstall the firmware. Sometimes the problem is solved in this way. It is also recommended to familiarize yourself with neighboring topics that have very useful instructions. Perhaps this will solve your problem.

Asking the question in the spirit of "Which firmware is the best?" At best, you will be sent to the cap under the spoiler "Survey Screenshots"!

Important information!

ATTENTION!!! Uvaga !!! ATTENTION !!! ACHTUNG !!!

Neither the authors of the manuals nor the authors of the firmware are responsible for your actions! Remember, all actions you do at your own peril and risk!

Instructions

VERY IMPORTANT

Before any manipulations with the phone, whether it is firmware, uninstalling applications, installing cores, overclocking the processor, modding the interface, etc.,be sure to make a full backup of the system. Just remember and know that neither I nor the author of the firmware is responsible for the harm done to your phone. You do everything at your own peril and risk!

To install unofficial (custom) firmware, you need to unlock the bootloader and install custom Recovery.


Attention!On some devices, released mainly in 2012 (less often in 2011), it is impossible to install Recovery (or installed, but does not start), as well as firmware. They must be specially adapted to the device, received the name "poltergeist 2012". For more information, as well as any questions related to this phenomenon, please contactthis topic.

Drivers

• USB Driver v3.0.0.021 (Installation on Windows 8 / Windows 8.1 and Windows 10)
  
• USB Driver v4.10.0.001 can be installed on Windows 8.1 / 10 after setting up the registry

Bootloader unlocking

• WildfireS Utilily (All-in-One)
  
• Instructions for unlocking the bootloader. Version "10 Steps"
  
• Instructions for unlocking the bootloader without registering with HTCDev.com (without losing the warranty)
  
• Script and set of utilities for Linux to get UNLOCKED and ROOT

Installation Recovery

• Install CWM Recovery 5.0.2.8 in one click. + Getting root rights (installing Superuser 3.0.7)
  
• Installing ClockWorkMod Recovery v.5.0.2.8 (CWM Recovery) via Fastboot for Unlocked or S-off devices
  
• Restoration of stock recovery or installation of any custom, method в„–100500
  
• Instructions for installing the recovery version * .img

Installing CyanogenMod series firmware

Using ClockworkMod Recovery v5.0.2.8 as an example

0. Go to the Recovery

1. Findwipe data / factory reset Yes - delete all user data
2. +++ Go back +++
3. mounts and storage format / system
4. +++ Go back +++
5. advanced Wipe Davlik Cache
6. +++ Go back +++
7. mounts and storage unmount / cache mount / cache
8. +++ Go back +++
9. install zip from sdcard choose zip from sdcard choose our firmware file .zip format Yes
10. We are waiting for the installation to be completed.
11. After everything has been successfully installed, clickreboot system now

Poltergeist cores

• Kernel for CyanogenMod 7
  
• Kernel for CyanogenMod 10, information on 2 types of poltergeist
  
• Kernel for CyanogenMod 10.1
  
• Kernel for CyanogenMod 11

Memory expansion

App2SD; a2sd; Link2SD; S2E (simple2ext)

• Transferring applications to an SD card (App2SD; a2sd; Link2SD, etc.)
  
• S2E (simple2ext)differs from data2sd and similar to the fact that you can choose what to transfer to SD; entire data folder or individual directories

INT2EXT

• How to expand the internal memory by means of scripts
  
• All versions of INT2EXT and the differences between them.

Other

• Resizing MTD sections
  
• Freeing up memory on HTC Wildfire S in 3 steps using Link2SD, Titanium Backup (TB) and ODEX

Recovery

ClockworkMod Recovery

CWM v6.0.5.3 from 08.18.2014
CWM v6.0.5.0 dated July 5, 2014
CWM v6.0.4.9 from 06.06.2014
CWM v6.0.4.8 + Manual
Topic onXDA
CWM v6.0.3.2
CWM v6.0.3.1
CWM v5.0.2.8
CWM v5.0.2.6

Team Win Recovery Project

TWRP v2.8.0.0 dated 09/20/2014
TWRP v2.7.1.0 from 06.06.2014
TWRP v2.7.0.0 / v2.2.0.0 + Manual
Topic onXDA

PhilZ Touch Recovery

PhilZ Touch v6.43.7 from 3.06.2014
Topic onXDA

OWL Recovery-Mod

OWL Recovery v1.0 beta
OWL Recovery v0.1.2

Firmware

CyanogenMod 7

Firmware from alquez

Topic onXDA
Kernel for "poltergeist 2012"
CM7 Firmware Archive by alquez

Firmware from ansatbay

CM9_ICS_BY_ANSATBAY_FINAL3 (CM7)
CM9_ICS_BY_ANSATBAY_FINAL4 (CM7)
SENSE 4.0 (CM7) ALPHA1

Firmware from other developers

• UltraBeam REVO V1.7 UB-Styled
  
• UltraBeam GB | Revolutionary V1.6 | Ubstyled
  
• Droidwfs
  
• WildJOY || JoyOS v1.2.2
  
• Aceonev2.2
  
• Jelly Bread v5.1
  
• Cm7-sense

CyanogenMod 9

Modpunk firmware

Note! Owners of CDMA devices must download the marvelC version! On CDMA GSM firmwareDO NOT START!
Topic onXDA
CM9 firmware archive from Modpunk

List of changes

ALPHA9 - 2012-11-06
* Core:
- Fix HQ video
* ROM:
- Support HQ video
- Updated to CM 9.1.0

ALPHA7 - 2012-07-27
* Core:
- Slightly reduced kernel size.
- Fixed Bluetooth initialization on marvelC.
* ROM:
- marvelc: Fixed audio and backlight modules.
- marvelc: Sending voice messages to your number (bug # 67)
- marvelc: fixed eri.xml

ALPHA6 - 2012-07-17
* Core
- Fixed Bluetooth initialization.
* ROM
- Several fixes for marvelC.

ALPHA5 - 2012-07-04
* Core
-
* ROM
- Camera artifacts fixed

ALPHA4 - 2012-07-04
* Core
- Added smartass2 processor mode. Now it is set by default (If you change the performance settings, then you need to select smartass2)
* ROM
- Added assembly for marvelC
- Minor performance improvements
- Fixed scanning of QR codes

ALPHA3 - 2012-06-21
* Core
-
* ROM
- Added CDMA support for marvelC
- Added support for panoramic photo
- Added elctronbeam animation
- Updated libhtc_ril.so
- Updated wifi software
- Fixed MMS profile
- Fixed network switching
- Fixed portable access point

ALPHA2 - 2012-06-01
* Core
- Fixed kgsl memory management (should fix Forced Close bugs)
- Added support for ZRam
- Added HTC TP calibration
* ROM
- Fixed graphic lags chip adreno 200.
- Added permissions for tty access.
- Added support for ZRam.
- UPSTREAM: Added Apollo Player.
- UPSTREAM: Improved lock screen support.

ALPHA1 - 2012-05-12
* Core
- Added SWAP support
- Added support for KSM
- Removed MSM Camera.
- Increased adsp memory to support camera
- Increased memory kgsl
* ROM
- Added support for video recording
- Fixed deep sleep mode
- Fixed loading animation size
- Fixed camera memory leaks
- Fixed issues with RIL permissions
- Fixed power profile
- UPSTREAM: Added support for themes.
- UPSTREAM: Added lock screen setting.

ALPHA0 - 2012-05-04
* Core
- First release
* ROM
- First release

Simplex Team firmware

CM 9.2.2 ICS PLUS + FAQ dated 07.24.2014
First release dated 07/20/2014

Firmware from htc0097

Download
Description

Firmware from other developers

• Speed ​​droid
  
• ParanoidAndroid v1.6a
  
• Cavefire
  
• Slimsandwich
  
• CM9 JELLY BEAN BY ANSATBAY

CyanogenMod 10

Firmware from niks255

Download
Topic onXDA

List of changes

[7.11.2014]
- Ported superuser from CM10.1 to replace the ancient Superuser
- Added button "Turn off" in flashlight notifications
- Ability to hide applications in the menu (Trebuchet)
- Switching 2G / 3G profiles
- Switching the call mode in profiles
- Application filtering modes in the menu: only system and only downloaded
- Removed unnecessary / non-working items in various menus
- Improved scrolling
- Fixed live wallpapers
- Added Simple2Ext
- Added blacklist of calls
- Improved performance
- Added localization
- Minor fixes and improvements.
[8.10.2014]
- Default language when first turned on - Russian
- Fixed camera crash when calling from the lock screen
- Fixed artifacts when resizing images in the camera
- Improved autofocus and increased camera stability
- Fixed playing HTML5 video in the browser
- Fixed graphic lock screen bug
- Fixed non-matching text in some places
- Removed all non-functional functionality: switch between MTP, PTP and Mass Storage, CM Stats and so on
- CM File Manager and Apollo replaced by Simple Explorer and Vanilla Music Player, respectively. Both applications are fully translated into Russian.
- Full system localization
[30.09.2014]
- Fixed crash of sms application when changing keyboard type
- Fixed auto-backlit buttons. Now her behavior is like on stock firmware
- Added flashlight in Quick Settings. Was previously unavailable
- Updated Russian translation and corrected text that does not fit into interface elements in some places
- Improved speed
- Improved scrolling

JDroid firmware

CyanogenMod 10.0 + MOD [Final: Release Candidate](experimental)
CyanogenMod 10.0 + MOD [Pre-Final](stable)
CyanogenMod 10.0 [Pre-Beta 2]
CyanogenMod 10.0 [Pre-Beta 1]

Reviews on firmware

Mini reviewon CyanogenMod 10.0 Final (Release Candidate)fromEyser
Comparative mini-reviewon CyanogenMod 10.0 Final-RC [mod]fromhelvetin
Detailed review onCyanogenMod 10.0 Pre-Final [mod]fromEyser
Mini-review onCyanogenMod 10.0 Pre-Final [mod]fromhelvetin
Mini-review onCyanogenMod 10.0 Pre-Final [mod]fromFlykigi

OWL Project

Thanks for the help and testing of new versions of firmware, you can express not only me, but also these people. Thanks to which I can quickly identify bugs and fix them.

Serjo87- Main tester
Tepp931- Tester
Flykigi- Tester
Eyser- Author of reviews and manuals
Jv666- Tester is a rare guest.the very first tester

Modpunk firmware

Topic onXDA
CM10 Firmware Archive from Modpunk

List of changes

ALPHA2 - 2012-12-13
* Core
- Fixed a problem with the memory of the camera.
* ROM
- Fixed HQ video playback.
- Fixed panorama shooting mode.

ALPHA1 - 2012-10-12
* Core
-
* ROM
- Reduced size
- Fixed animation in the status bar
- Fixed black screen
- Added config_wifiApStartInterface for tethering
- Added new configs.
- Fixed problem with falling off the Internet.

ALPHA0 - 2012-08-30
* Core
- First release of CM10
* ROM
- First release of CM10

Simplicit firmware

Yandex Disk

Jelly king

Topic onXDA

Reviews on firmware

Comparative mini reviewfromEyser
OverviewfromSvifts
Overviewfromken-san
Overviewfromankar84

BlackBean6

ATTENTION! THIS FIRMWARE IS INTENDED ONLY FOR CDMA DEVICES! ON GSM IT WILL NOT BE INSTALLED!
Topic onXDA

ParanoidAndroid v2.54

Topic onXDA
Inadequate ReviewfromJv666

Tw5 jb rom

Topic onXDA
Review in picturesfromken-san

Firmware from other developers

• *** BLU MOD v1.1 ***
  
• Speed ​​droid
  
• AOKP
  
• Cyanogenmod 10 by benjamingwynn
  
• Jellyfish
  
• MarvellousPAC

CyanogenMod 10.1

Firmware from niks255

Download
Patch in case of incompatibility
Topic onXDA
Firmware archive

List of changes

[06.01.2015]
- Automatic sms-mms conversion is disabled.
- Improved work with multimedia (recording / playback of audio and video)
-Added download speed display in download manager notifications
-Small fixes
[18.12.2014]
-Added management of permissions for installed applications in Settings - Security
-Updated graphics of some applications
- Improved stability and energy saving
[08.12.2014]
- Improved performance
-Added "add" button in quick settings
-Added internet speed indicator in status bar
-Added mobile Internet switch to the first settings page
-Now you can turn on the appearance of the status bar for a short time in full screen mode with incoming notification
-Ported weather clock widget from CyanogenMod 11
-Added sidebar for placing application shortcuts
-Status bar in fullscreen mode is now called by swipe from the top edge
-New voice recorder
- Removed Privacy Guard alert from bar status
-Added support for CIFS and tunneling
-Added localization
[16.10.2014]
-The default language is now Russian
-Fixed video playback in the gallery
-Fixed lock screen bug
-Fixed Bluetooth headset
-Fixed text fixed
-Added the ability to make a flashlight in the quick settings
- Fixed turning off the flashlight when the screen is turned off
-Added the ability to set live wallpaper as a background
- Removed idle functionality
-Added localization
-Apollo and CM File Manager replaced by Vanilla Music Player and SimpleExplorer
-Other fixes and improvements
[13.09.2014]
- Added OTA update
[04.09.2014]
- New core (+ Update from 09/06)
- Improved performance
[02.09.2014]
- Fixed problem with video playback
[01.09.2014]
- New core
- Added poltergeist support
- Fixed Wi-Fi tethering encryption
- Fixed various crashes and memory leaks
- Updated translation
- Improved stability and performance
- Fixed 802.11n support
[24.08.2014]
- Fixed headset bug
- Fixed SystemUI memory leaks
[23.08.2014]
- Fixed USB tethering
- Fixed WiFi tethering (encryption still does not work)
- Fixed crash of the application "Settings"
[22.08.2014]
- Fixed encoding / decoding of some file formats

OWL PROJECT firmware [JDroid]

CyanogenMod 10.1 Release Candidate v3 from 06.16.2013
CyanogenMod 10.1 Release Candidate v2.1 from 05.27.2013
CyanogenMod 10.1 Release Candidate v2.0

[пїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅпїЅ] download

from 25.05.2013
CyanogenMod 10.1 Release Candidate from 17.05.2013
CyanogenMod 10.1 Post-Beta

Topic onXDA know our
JDroid CM10.1 Firmware Archive

IH8ra firmware! N

CyanogenMod 10.1 with Android 4.3 Features
Topic onXDA

Firmware from other developers

• AOKP
  
• PAC-man v23.0.0
  
• ParanoidAndroid v3.65
  
• ChameleonOS
  
• Kevinjoa firmware
  
• Sense в„ў 5 look-and-feel

CyanogenMod 10.2

Simplicit firmware

cm-10.2-20140427-UNOFFICIAL-marvel.zip (100.69 MB)

Topic onXDA

CyanogenMod 11

Firmware from Simplicit / Androidarmv6

CyanogenMod 11 NIGHTLY dated 8.03.2015
CyanogenMod 11 FINAL 12.02.2015

Kernel for "hard cases"
Topic onXDA

Old firmware

CyanogenMod 11 RC14 STABLE from 01.05.2015
CyanogenMod 11 RC13 STABLE from 1.12.2014
CyanogenMod 11 RC12 STABLE dated 11/02/2014
CyanogenMod 11 RC11 STABLE from 2.10.2014
CyanogenMod 11 RC10 STABLE from 09/13/2014
CyanogenMod 11 RC9 STABLE from 12.08.2014
CyanogenMod 11 EXPERIMENTAL BETA1 from 15.06.2014
CyanogenMod 11 EXPERIMENTAL BETA1 from 06.14.2014
CyanogenMod 11 WEEKLY from 05.29.2014
CyanogenMod 11 BETA1 from 19.05.2014
CyanogenMod 11 KEVIN’S HOMEMADE from 18.05.2014
CyanogenMod 11 from 05.16.2014
CyanogenMod 11 With HALO from 05.05.2014
CyanogenMod 11 from 05.05.2014
CyanogenMod 11 from 03.05.2014

Nightie

CyanogenMod 11 NIGHTLY on November 8, 2014
CyanogenMod 11 NIGHTLY from 11.11.2014
CyanogenMod 11 NIGHTLY dated 10/31/2014
CyanogenMod 11 NIGHTLY dated 10.25.2014
CyanogenMod 11 NIGHTLY dated 10/18/2014
CyanogenMod 11 NIGHTLY from 10.10.2014
CyanogenMod 11 NIGHTLY on 10/04/2014
CyanogenMod 11 NIGHTLY from 09.27.2014
CyanogenMod 11 NIGHTLY dated 09/20/2014
CyanogenMod 11 NIGHTLY from 09/14/2014
CyanogenMod 11 NIGHTLY from 09/06/2014
CyanogenMod 11 NIGHTLY from 08/30/2014
CyanogenMod 11 NIGHTLY from 08.23.2014
CyanogenMod 11 NIGHTLY from 08.19.2014
CyanogenMod 11 NIGHTLY dated 08.16.2014
CyanogenMod 11 NIGHTLY from 10.08.2014
CyanogenMod 11 NIGHTLY dated 08/09/2014
CyanogenMod 11 NIGHTLY from 7.08.2014
CyanogenMod 11 NIGHTLY dated July 25, 2014
CyanogenMod 11 NIGHTLY dated 07.24.2014
CyanogenMod 11 NIGHTLY dated 07/21/2014
CyanogenMod 11 NIGHTLY from 07/19/2014
CyanogenMod 11 NIGHTLY dated 07/17/2014
CyanogenMod 11 NIGHTLY from 07.15.2014
CyanogenMod 11 NIGHTLY dated 07/14/2014
CyanogenMod 11 NIGHTLY dated 07/12/2014
CyanogenMod 11 NIGHTLY dated 07/11/2014
CyanogenMod 11 NIGHTLY dated July 5, 2014
CyanogenMod 11 NIGHTLY from 07/01/2014
CyanogenMod 11 NIGHTLY from 06.28.2014
CyanogenMod 11 NIGHTLY from 06.26.2014
CyanogenMod 11 NIGHTLY from 06.21.2014
CyanogenMod 11 NIGHTLY from 06.20.2014
CyanogenMod 11 NIGHTLY from 06/18/2014
CyanogenMod 11 NIGHTLY from 06.16.2014
CyanogenMod 11 NIGHTLY [unstable]from 13.06.2014
CyanogenMod 11 NIGHTLY [unstable]from 12.06.2014
CyanogenMod 11 NIGHTLY [unstable]from 11.06.2014
CyanogenMod 11 NIGHTLY from 10.06.2014
CyanogenMod 11 NIGHTLY from 9.06.2014
CyanogenMod 11 NIGHTLY from 07.06.2014
CyanogenMod 11 NIGHTLY from 06.06.2014
CyanogenMod 11 NIGHTLY from 4.06.2014

Omnirom

Simplicit firmware

OmniRom HOMEMADE from 05.29.2014
Omnirom from 4.05.2014
Omnirom from 01.05.2014
Topic onXDA

AOSPA - ParanoidAndroid 4.6

Simplicit firmware

AOSPA - ParanoidAndroid 4.6 NIGHTLY from 10.10.2014
AOSPA - ParanoidAndroid 4.4 - FINAL from 2.07.2014
AOSPA - ParanoidAndroid 4.4 - RC2 from 06/18/2014
AOSPA - ParanoidAndroid 4.4 - BETA1 from 06.06.2014
Topic onXDA

AOSP Edition

Firmware from niks255

AOSPE-1.0.0.1 [ALPHA] from 12/31/2013

GApps

• Google Apps [Lite] CM10 by JDroid from 11/24/2012
  
• Google Apps [Lite] CM10.1 by JDroid from 13.05.2013
  
• Google Apps for CM 9/10 / 10.1 / 10.2 / 11 from 03/16/2014
  
• Google Apps for CM 11 Install only when you have already launched the firmware at least once!
  
• Google Apps for CM 11 from 06/18/2014 Install only when you have already launched the firmware at least once!

Screenshots

CyanogenMod 9

CyanogenMod 10

CyanogenMod 11

Bugs / Glitches

CyanogenMod 7

GPS may not work.Fix
Proven on the latest firmware from alquez

CyanogenMod 9

Free from bugs
Proven on the latest firmware from htc0097

CyanogenMod 10

Black screen for incoming calls (not everyone hasfix)
Proven on the latest firmware from niks255

CyanogenMod 10.1

I'm free, I forgot what a bug means, I'm free ...well, you understand
Proven on the latest firmware from niks255

CyanogenMod 10.2

1. The camera does not work
2. USB tethering does not work
3. Wi-Fi tethering does not work. Only third-party software:Wireless tether (Instruction), OpenGarden WiFi Tethering, WiFi Tether Router
4. Noises instead of the interlocutor's voice / music when connecting a Bluetooth headset

CyanogenMod 11

1. Modem mode does not work: WI-FI (Fix), USB, Bluetooth
2. GPRS / EDGE falls off (3G works)
3. ART does not work for ArmV6

Omnirom

1. Same as CM11
2. The camera does not work
3. Noises instead of interlocutor / music when connecting a Bluetooth headset

AOSPA - ParanoidAndroid 4.6

1. Same as CM11
2. LED does not work when charging
3. Noises instead of interlocutor / music when connecting a Bluetooth headset

Survey Screenshots

Post has been editedPinich2517 - 08.03.17, 09:08

Reason for editing: Removed dead links

[Mr.BioCry]

In the last core for cm7 there is a Governor car (processor behavior regulator) and a small I / O Scheduler cart (I / O scheduler)

for myself, I determined the optimal Governor, but it was interesting to find a description of others, so I found:

Brief description of regulators:

brazilinawax - no description found yet. All that is known is based on interactive. Almost the same as Smartass.

ondemand - Available in almost all kernels and in many is default (by default). When the CPU load reaches a certain upper threshold, this control quickly raises the frequency of the processor to respond to the request, then gradually reduces the frequency of the CPU when it is no longer needed.

ondemandX - changed sensitivity and added sleep mode.

conservative - Available in some kernels. It is similar to the ondemand regulator, but will increase the frequency of the CPU more gradually (not so fast) to better fit the request. This regulator provides less sharp response, but may save the battery better.

interactive - Has a different approach. Instead of sampling the CPU at a certain frequency (level), it will raise the frequency when the processor goes out of idle mode. When the CPU goes out of idle, the timer is configured to start within 1-2 ticks (CPU cycle). If during this time (since the processor leaves idle mode before the timer starts) the processor is 100% loaded, then it is considered not to be overclocked enough and the frequency rises to the maximum value. If the CPU was not 100% busy, then the regulator evaluates the CPU utilization for the last 'min_sample_rate' (default 50,000 Ојs) to reduce the frequency to the required level. This regulator is considered to be more interactively responsive to various processor loads. The only configurable parameter is the time during which the processor will remain on one frequency or another before the descent begins (50,000 Ојs).

interactiveX - supplemented by interactive code that blocks the CPU at the lowest frequency when the device screen is turned off. It has a sleep + wake profile, meaning that you don’t have to manually set the Screen Off profile in SetCPU.

lazy - based ondemand with the additional parameter min_time_state to indicate the minimum time during which the CPU remains on the frequency before decreasing / increasing the last. The idea is to remove any instability caused by a rapid change in the ondemand frequency. This controller polls the state much more often than ondemand, but changes the frequency by one step only after the min_time_state expires. It also has a screenoff_maxfreq parameter, which can be set to determine the maximum screen-off frequency.

lagfree is quite similar to ondemand in terms of source code and its design and purpose. The difference in its optimization for better stability and "sharpened" in a loaded environment. The frequency delicately decreases and increases, instead of immediately jumping to 100% when speed is needed.

lulzactive - default in the core Lulz. Based on interactive. With the profile of the disabled screen as interactiveX and some features of smartass.

minmax - Conservative adaptation, but with very good performance. A very nice regulator with a good battery life.

performance - Available in some kernels. Will keep the CPU at the maximum set frequency all the time. This is more efficient than setting min and max at the same frequency and leaving the ondemand regulator, because the system will not waste resources on checking the CPU utilization rate.

powersave - Available in some kernels. Will keep the CPU at the minimum set value all the time.

userspace - Allows a user or program with root privileges (works with UID 0 - root) to install the processor at a specific frequency through the scaling_setspeed file in a specific directory.

SavagedZen - no description found yet. All that is known is based on interactive. Another one is very good and balanced modification Smartass.

smartass - (erasmux @ XDA). Fully rewritten interactive control. The CPU spends more time at lower frequencies to improve battery life. Also gives the Screen Off profile, staying at the minimum frequency when the phone is not active (in idle mode).

smartassV2 - many customizable options. Quickly responding to changes in CPU utilization, based on the idea of ​​interactive. The threshold of the "ideal frequency" is also adjusted (as in lulzactive) and the controller above this frequency behaves more aggressively than in the lower zone. In sleep mode, another, also customizable, “ideal frequency” is used.

smoothass - a slightly more aggressive smartass

Description of I / O Schedulers:

Complete Fair Queuing (CFQ) I / O Scheduler

The CFQ Planner uses a different approach to achieve the same goals. In cfq everyone
The process is assigned its own queue, and a time slice is assigned to each queue.
(timeslice). The I / O Scheduler rounds each queue and serves requests.
from the queue until the time limit is reached (timeslice) or remains
requests in this queue. In the latter case, the CFQ scheduler will wait by default.
10-ms, new request from the queue. If the wait was in vain, then the scheduler goes to
the next turn.

Within each process queue, synchronized requests (such as reading)
take precedence over unsynchronized requests. Thus, CFQ promotes reading
and prevents the problem of writes-starving-reads.

The CFQ scheduler works well for most tasks, making it a great first.
by choice.


Noop I / O Scheduler

The NOOP Scheduler is the most basic scheduler available. He does not perform what
sorting, only major mergers. It is used for specialized devices,
which do not require sorting their queries.

Deadline I / O Scheduler

Deadline I / O Scheduler stores a queue sorted (as described above, comment), and
introduces two additional queues: a FIFO queue for reading and a FIFO queue for writing. Records
in each of these queues are sorted by arrival time (in fact, the first one entered is
first came out). Each request in the FIFO queue is assigned an end time. For the queue
read requests are 500 milliseconds. For a write request queue, this is five seconds. With
receipt of a new I / O request, it is inserted-sorted into the standard queue and
placed at the end of the corresponding (read or write) FIFO queue.

As a rule, I / O requests from the standard head are sent to the hard disk.
sorted queue. This maximizes overall throughput while minimizing
search operations and installation of heads on the disk, since the normal queue is sorted by
block number (as with Linus Elevator).
When an entry at the beginning of the list of one of the additional FIFO queues has an assigned
time, the I / O scheduler stops processing I / O requests from the standard queue, and
starts servicing requests from this FIFO queue. I / O scheduler checks and processes
requests only from the head of the queue where the oldest requests are located.

Thus, Deadline I / O Scheduler supports efficient overall throughput.
without fasting any single request is unacceptable for a long time. Problem
writes-starving-reads is reduced to a minimum.

Simple I / O scheduler (SIO)
SIO is based on the deadline, but it looks more like a mix
between noop and deadline. In other words, SIO looks like a lightweight deadline version, but it
does not perform sorting, so it is designed mainly for random access
to disk (such as SSD hard drives), where a sorting request is not necessary (since
any sector can be available at any time, regardless of its
physical location)

I apologize if not vopad =)

INFA was taken from here:Samsung GT-I9100 Galaxy S II - Modified and stock cores

Post has been editedPinich2517 - 13.06.14, 17:53

Reason for editing: link

[ansatbay]

CM9_ICS_BY_ANSATBAY_FINAL3 HERE

[ansatbay]

CM9_JELLY BEAN_BY ANSATBAY (CM9) HTC Wildfire S - Firmware CM9 ICS BY ANSATBAY (CM7) (OS 2.3) (Post # 14419187), we discuss there, we say thanks, we make our proposal

CM9_JELLY BEAN_BY ANSATBAY (CM7) right

Post has been editedansatbay - 16.07.12, 17:48

Reason for editing: CM7 JELLY

[helvetin]

Freeing up memory on HTC Wildfire S in 3 steps using Link2SD, Titanium Backup (TB) and ODEX

(for those who do not have an ext partition, S-OFFa for the ability to edit sections of internal memory and for those who constantly, after each update of the firmware, puts (restores) the same cumbersome applications into a deficient internal memory)
1. Background
Put today SM9 A7, restored through TB ​​applications. I did not have time to rejoice how the message about the lack of internal memory came out. I have long wondered where to put various applications (such as Fancy), which take up a lot of memory and can’t be moved to a USB flash drive (for widgets cannot be, and autorun applications). So to say, gathering thoughts in a heap, reading a lot of material and turning on the head, that's what happened
2. Release
2.1. Standard method
This message has already pretty much turned me on and I decided to deal with the lack of memory once and for all. Cleaning up the cache, cache, and moving applications to the memory card gave me about 20 MB of free memory. (Brief instruction We open the TB-menu-clearing the davick cache; again, the TB-batch backup and restore-clearing the cache \ data (but I never clear the data, because I’m sorry for accounts, bookmarks, etc.).
It seemed a little and then I decided to experiment.
2.2. Experiment with system memory.I decided to free up the system (269 mb) by removing, in my opinion, unnecessary applications and move my applications from the “precious” available phone memory (150 mb) there, which I always have. I removed the following applications from system memory.
-standard launcher-trebuchet (alternative Apex)
speech synthesizer
keyboard (alternative swipe)
- wallpaper android
-vocal search
As a result, the internal memory was 31 mb, and the system memory is as much as 69 mb.

Then I began to move my applications there - Apex Launcher (with the downloaded theme of the sense), Fancy widget, ec task manager, etc .; Integrated Market and Gmail updates into system memory. As a result, of all the applications that I had in my internal memory, only Swipe remained (I didn’t want to be a system one).

The result was impressive.

But this seemed to me a little and I decided to do Coke.
Screen of my desktop (as proof that everything works)

2.3. Odex
I have simplified the instructions a little.
1. downloadodex.zip(733 bytes)
(ThemeXDA)
2. downloadreodex_win.zip(826.72 KB)

3. unpack the script somewhere on the computer
4. go to the script in the reodex_win \ odex folder and replace the file with the one you downloaded in the first paragraph.
5. Start the phone in recovery mode - make mount data \ system
6. in the script run the Windows odex script
7. we wait ......
8. after finishing the encoding, we do wipe cash and in the advanced menu we do wipe dalvick cash
9. reboot the phone
We check the memory and there ....

P.S. Keep in mind that the free space in the system memory will decrease significantly after encoding. Therefore, leave meters 50-55 before the process. (I have decreased to 45 MB somewhere)
Good luck in your endeavors and endings! ;): D

Post has been editedPinich2517 - 07.06.14, 08:19

Reason for editing: Corrected

[QClick]

More or less normal operation of the camera in CyanogenMod 9

(small jerking, jerking, etc.)
Install the applicationLG Camera

Set the settings as in the screenshot:

To play the video on the phone setMX Player + WFS codecs

Post has been editedPinich2517 - 08.08.14, 14:55

[Rushmore]

GAPPS installation features

When installing gapps, the rights to system files are slightly changed and some files from the main firmware are replaced. Before installing, I recommend throwing files out of the gapps distribution:

MarketUpdater.apkno longer needed, because modern versions of the market 3.x can update themselves
VoiceSearch.apkyou still have to reinstall it through the market, otherwise it does not work


Market client itselfPhonesky.apkand its services can be immediately replaced with the current version, so as not to wait for the update. The current version can be downloaded in the profile branch byGoogle Play Store

Post has been editedPinich2517 - 12.06.14, 08:35

Reason for editing: corrected

[Rushmore]

Who has problems with GPS in CM9, try this fix:cm9-gps-fix.zip(171.55 KB)


My companions began to cling much faster. Suddenly help you?

Install from CWM recovery. Tested on Alpha6 and Alpha7 from Modpanka. The package contains the following files:

/system/lib/hw/gps.marvel.so
/system/etc/gps.conf
/ system / etc / SuplRootCert

But backup is still best done before installation, just in case))

Post has been editedPinich2517 - 26.09.14, 15:48

Reason for editing: Corrected

[ansatbay]

I bought myself a light)

M

Please do not flood.

Post has been editedDaymon - 12.10.12, 10:46

[Jdroid]

evgen0791,So that I know. did not watch. Now it is worth a lot of things already.

I've found a chip here, how to make the firmware 15 MB smaller. I'll try to cut back.

M

It is not necessary to write more in a row for several posts, use the Edit button and add information to your last post in the topic. Do not hammer the topic.

Post has been editedDaymon - 14.10.12, 22:44

Reason for editing: Combined posts.

[Dymon]

M

Colleagues, you are in the topic HTC Wildfire S Firmware - CyanogenMod, this is a profile branch, you do not need to communicate in it as in a bobbin or in a chat, the player is not discussed here, etc. that does not have a relationship to this firmware, this firmware is discussed here bugs, laid out links to new versions.
Verbal warning!
Cleaned the topic.

Post has been editedDaymon - 16.10.12, 18:58

[Dymon]

M

Dear colleagues, the topic has already been a warningHTC Wildfire S - CyanogenMod Firmware (OS 2.3, 4.0, 4.1) (Post # 16315622)which was successfully ignored by Jdroid.
Recall aboutForum Rules!
P. 4.21. I recommend to finish the discussion on the actions of representatives of the Administration in public, you should also end up flooding and the offtopic that was here, discuss the CyanogenMod firmware in this topic and nothing more, the branch line, and not one of the topics in the Trepler section.
A warning. Cleaned the topic.

Post has been editedDaymon - 18.10.12, 08:27

[Jdroid]

CyanogenMod 10^{preBeta 1}

Android version 4.1.2

General information:
Stage:Beta
Version:PreBeta 1
Date of release: 21.10.2012

Firmware info:
OS version: 4.1.2
Kernel version: 2.6.35.13
Communication module version:47.23e.35.3038H_7.57.39.10M
CyanogenMOD version:CRYPTOMILK-preBeta 1

Start:
At the moment, the firmware is going to the stageBeta . For a little bit we step and fix bugs and other not good things.
This release is in the titlePrebeta , why is that? The answer is, due to strange circumstances, the file from the kernel disappeared from me, without which I cannot assemble it. Replace the file does not work, you need to pack everything on the new. Actually for this reason you get PreBeta on the old core.

Indirectly changed a lot without a kernel, although there are some bugs. Well, where without bugs now, we will rule.

Changelog:
Important
- Added support for Live Wallpapers
- Removed Google Services[Google Paly, Google Now, Voice Search, Google Talk, Gmail]
- Removed Beats Audio Engine
- Added new bootanimation[Jelly Bean
- GPS fixes [increase search speed, etc.]
- Fixed WI-FI [reduced network search timeout, extended WI-FI adapter distance]
- Internet fixes [problem with the fall of the Internet]
- Removed Tethering
- Fixes memory mapping
- Cache flush fixes [unused applications]
- Fixes responsiveness tacha
- Battery fixes
- Disabled "Setup Wizard"

System
- Fixes "Dialer"[phone.apk]
- SMS / MMS Fixes
- USB-SDcard Fixes

Added by:
- Link2SD application
- ROM Manager
- New Apollo Music
- Apex Launcher [main]

Deleted:
- Nova Laucnher
- gmail
- Google Now
- Google Play
- gtalk

Bugs:
- HQ YouTube -does not work.
- Video player -does not work.
- Video camera -does not work.

Pros:
- Improved interface smoothness.
- Improved active border display interface.
- Multitasking.

Installation:

1. Go to Recovery.
   
2. Making Wipe All [Wipe all + Wipe davlik cache + Wipe Battery stats]
   
3. We do Format / boot, / cache, / system, / data
   
4. Go to Install zip from sdcard and so on.
   

Troubleshooting:

If the phone still does not respond and does not want to go out and sleep.

1. Disable "" Automatic brightness "
   
2. Disable "Auto-rotate screen"
   
3. Set the frequency200MHz - 806MHz or leave the default settings.
   
4. We leave on the point back, go to the "Surface smoothing", select the last paragraph "Remove color bars and blurry effect."
   
5. Reboot, try.
   

Or turn on the mode"ondemand"and play with the frequency of the processor.


Download:
CyanogenMod_10_CRYPTOMILK_PreBeta-1_Marvel_by_JD_Team.zip[120MB]Refill required

Post has been editedPinich2517 - 09.12.14, 15:58

Reason for editing: Minor fixes

[Serjo87]

Jdroid,
When to expect? Today?))

M

Check outRules section "Android - firmware"
P. 3.2. It is forbidden to ask questions that are not directly related to a specific topic, do not carry a semantic load and have a clearly stimulating character (especially such as "When will you lay out?", "How long should the firmware be?" And the like).

Post has been editedDaymon - 21.10.12, 23:39

[johnny2007]

Drive mode works fine.

[AndreJarwis]

Thank you so muchJdroidfor the firmware!
Everything is comfortable and smooth :)
Yuzayu it about 5 hours, normal flight
A small review of bugs and firmware:
From bugs I noticed only:
-Google Play Error"Not enough free memory to install the program" although there is enough memory for the program
How to decide, not yet aware
- Does not connect to the computer via usb
The most terrible bug.UPD- DearJdroidWrote that everything is fine, I will try to reflash. Full wipe did. How to reflash - accomplish your goal)
-Artifacts on the camera preview
Minor bug, fotka normal - and this is important
- Bad exit from sleep
I decided to turn off the auto-rotation, increase the processor frequency (200-806 MHz), as described in the header: СЉ
-Does not work in Google Now
-By the wayVOICE SEARCH WORKS!:)
* And this is probably not a bug, just a little inconvenience-No Russian keys in the call(RespectedJdroidAlready unsubscribed that I simply forgot to replace the dialer, today will be fixed)
The rest of the flight is excellent. Thanks againJdroidI'm really looking forward to your finished firmware, if you do of course. Do not throw this case, your JB is the best!
Now I will reflash again, maybe some bugs will be lost.
By the way, on the main screen pleased tsiferki notifications :)
That's all, looking forward to the full JB for our fire

Post has been editedAndreJarwis - 22.10.12, 15:00

[Sharktopus]

And so it means to me.
Play market-works
USB connection works
A bad way out of sleep, I can’t say simply if you meant that only after the second pressing of the power button it turns on.
Well, with the camera, it's clear-everyone has artifacts here.
The main bug is a black screen with an incoming call and the inability to answer, I decided as follows, since all the tips and recipes that gave me yesterday did not help, and I reshooted, but this bug remained.
In general, what I did, went Lock screen --- Screen security --- Delay when locking --- Delay after timeout set --- no and Delay after turning off the screen --- no.
All and after that incoming calls began to be displayed and received immediately.
I do not know, most likely it all depends on the devices, because it is strange that someone has bugs, someone does not.
Lags by the way, and I have not slowed down.
And because of the keyboard will have to reflash?
JDroid Respect and Respect.

Post has been editedSharktopus - 22.10.12, 15:38

[di-s]

Could not resist ... set ...

HBOOT - 1.09.0099
RADIO - 7.57.39.10M
CMR 5.0.2.8
usb works
Black screen and Internet do not know yet (not enough time)

Impressions are positive, the response is really less. No new glitches. I'm testing.

JdroidAnd where are the letters on the call buried? I tried the phone.apk replaced with the old one - it did not help ...

[Bogdanish4e]

Ruskein @ 10/23/2012, 1:44 PM

Apparently crooked set)

smart divorced look ...

M

Please do not flood.

Post has been editedDaymon - 23.10.12, 14:38

[1C_Nick]

Good day to all! It turned out finally eliminateBlack Screen Problem!
Checked for 3 hours - normal flight: When incoming calls shows who is calling.

I did the following:
1) Settings>Performance>Processor: Min frequency - 200 MHz, Maximum - 806 MHz, Jack "Expose at boot" - Active;
2) Apex settings>Advanced settings: Daw "Stay in memory" - Active;
3) Reboot the phone.

Try it, maybe it will.

[Mobidick]

Mentr @ 10/22/2012, 20:59

Tell me in the last night cm9 data2 works? if so you can link)

I have a cm10 Alpha 0 (cm-10.0.0-RC0-CRYPTOMILK-ALPHA0-marvel). So, data2sd from the header did not work on it.
Found and tried at your own riskfrom here.
Direct link todownload.

Installation through the recovery worked very quickly. But I had to wait a bit while loading. In the end, everything is fine.