Can I flash PDAs of all HP iPAQ hx2 *** {b} series from WM6.5 to WM6.1 or WM5.0?

The firmware here can not flash only the PDA series "WITH ".
And firmwareWM5 , WM6.1 , WM6.5 interchangeable in any sequence, i.e. can...

Post has been editedsnakekvv - 14.04.11, 06:54

Error Error 503: ActiveSync Problem in Windows XP:

READ CAREFULLY !!!

1. Here: Flashing from wm2003 to wm5
   
2. And here: Flashing from official wm5 to any non-official firmware (wm5, wm6.1, wm6.5)
   
   
3. Or:
   Preparing a PDA for flashing
   
   • ExecuteClean reset .
     
   • Enter modePRE-BL (Pre-Bootloader) .
     Note:If you are the owner of the hx2 * 90b device, the screen will turn white (continue the process of flashing), otherwise you will see the inscription Pre BL.
     
   • Connect the device to the cable or cradle.
     
   • Press the button[The calendar] (!!! ->mandatory condition for flashing !!!).
     Note:PDA is determined by the computer only after pressing the button[The calendar] i.e. after clicking the [Calendar] button, drivers are installed and the device is initialized in the system.
     Note:On the hx2 * 90b device, nothing will change (shake blind, nothing terrible), for the rest, the inscription on the bottom left will change fromUSB ConnectedonUSB. Check whether you did everything correctly, you can open the Device Manager and make sure that the device is present [Windows CE Device ->HP USB Sync].
     
   
   
4. And the last option: if nothing helps, roll back to the original firmware Downgrade to wm2003se because she does not require treatment PRE-BL (Pre-Bootloader) and go through the whole chain of firmware again - Flashing from wm2003 to wm5 and then Flashing from official wm5 to any non-official firmware (wm5, wm6.1, wm6.5)
   
   

Post has been editedsnakekvv - 20.11.11, 22:12

Error Error 503: ActiveSync Problem in Windows 7:

QUESTION:

Nar message from 23.3.2011, 13:36

• People, something I have problems with flashing.
  I go Pre-BL, I press the calendar, the computer makes a distinctive sound connecting devices, I launch UPDATE_TOOL, it tries to connect to the PDA and issues Error503: ActiveSyncProblem.
  The driver for Windows7 installed, WinMobileCenter perfectly connects to the PDA ...
  ... So, I just tried to upgrade to a computer with Windows Vista ... the same Error 503
  

Nar message from 1/25/2011, 11:55

• I beat the alarm, as my independent dances with a tambourine and shamanic songs apparently no longer impress this shabby plastic brick with a screen ...
  Task:
  Install WM6.5 Tomahawk v8t Spiaatie to WM6.5 Tomahawk v6 Spiaatie
  Iron:
  PDA: Windows Mobile 6.5 v6 Spiaatie, HP iPAQ 2490b
  PC: Windows 7 32bit
  Process:
  1) I charge up to 100%
  2) I do Hard Reset
  3) I entered Pre-BL by pressing the combination Contacts + iTask + Reset, the screen turned white
  4) I put the PDA into the cradle with the USB connected and the power adapter into the outlet
  5) I press the calendar. The computer makes a distinctive sound of the device connection
  6) I install drivers from the folder with the USB_Vista_W7_Drivers_32bit firmware
  7) The Device Manager sees the PDA as "Mobile Devices ->HP USB Sync "
  8) I run UPDATE_TOOL from the folder with the firmware. I tick, click Next>
  9) The “Verifying the information on your iPAQ Pocket PC” process is in progress for about a minute, then Error 503: ActiveSync Error and the Exit button crash.
  
  I tried to run from another computer on Windows Vista, the same error.
  I tried other firmware with the substitution of the .nbf file, Error 503 error
  In normal mode, the PDA and Comp are well-connected to each other through the Windows MobileCenter.
  The strange thing is that before that I was upgraded from WM5 to WM6, later to WM6.5.SPv6 Spiaatie. All without problems, but now it does not work ... I wondered if the problem could be in ROM'e v6 itself !?
  Here it is no longer necessary, and I would say excitement ...
  

ANSWER1:

madkoshak message from 1/25/2011, 14:12

• 6) I install the driver from the folder with the USB_Vista_W7_Drivers_32bit7 firmware) The Device Manager sees the PDA as "Mobile Devices ->HP USB Sync "
  
  I should see how "HP USB Sync-Spiaatie ".
  In the list of drivers you choose the right one? They are there 2- HP usb sync from microsoft and HP usb synk spiaatie from Spiaatie itself :)
  

snakekvv

• in Russian and in original:
  Instructions for installing USB drivers for HX2000 in Windows Vista & Windows7 from Spiaatie
  

ANSWER2:

Drivers from Spiaatie in Windows 7 are not installed [x64]

Post has been editedsnakekvv - 10.01.12, 08:12

How to merge ROM dump from hx2 ***?

The procedure for removing the dump is 100% harmless and does not affect the warranty (did it on your device) - just a copy of the contents of the ROM:

1. Download the utility:http://www.hjgode.de/dev/grabit/(AutoRun_armV4i.exe)
   
2. Copy the utility to the root of the memory card. The card should be free about 150mb.
   
3. Run the utility.
   
4. We do not press anything - we wait a couple of minutes - maybe more (depending on the speed of the card).
   The utility makes a full memory dump of the device - I have the size of the dump filedump.bin It turned out 134 217 728 bytes.
   

Then we work with a dump on the computer:

1. Save to dump file nk.nba the contents of the dump file from 0С…0000000 to 0С…2FFFFFF = 50 331 648 bytes
   
2. We convert from nba format to nbf format - we consider the CRC32 checksum - it should converge and voila, you can flash it !!!
   

PS: The above was done for the device HP2790b.

OriginalmessagefromRaf_z

Post has been editedsnakekvv - 10.01.12, 08:12

Spiaatie drivers are not installed in Windows 7 [x64]:

snakekvv

• if you have Windows 7x64 and the drivers are not installed in any:
  1. - you can flip from Windows XP mode toWindows Virtual PC(orVMware Workstation).
  2. - press F8 when Windows 7 starts, then disable the digital signature verification of drivers. Windows 7 will boot in test mode. Install not signed drivers, flash PDAs, reboot Windows in normal mode.
  3. - find a PC with the installed Windows XP OS and reflash on it))).
  4. - step-by-step guide on signing and preparing hardware device drivers
  

Post has been editedsnakekvv - 10.01.12, 08:17

Error "RUUClientDriver.dll can't initialize device":

RomkaMegadeth
The firmware reaches 0.1% and the flash driver swears that RUUClientDriver.dll does not match the device. On this, sobsno, and stops ...

NeverGone
"RUUClientDriver.dll can't initialize device" means that the device is not sewn fromPre-BL(and mine againRussification hpRUUsavesworldnot knowing English users)

Post has been editedsnakekvv - 10.01.12, 08:23

What loader is needed for transitions between 6.0 - 6.1 - 6.5 different builds?

For the entire process of flashing, you can use the same bootloader "hpRUU.exe "from the archive" sp33205.exe "either from the archive" 1_hx2xxx_1.00.00.L_en.wm5.rar ".

Note: In order not to get confused in the flashers and their versions, it is STRONGLY recommended to upgrade one by one in steps, as written in the FAQ:
Flashing from wm2003 to wm5
Flashing from official wm5 to any non-official firmware (wm5, wm6.1, wm6.5)

Post has been editedsnakekvv - 10.01.12, 09:27

Firmware for HP iPAQ hx2000CSeries

Compatibility (Compatibility):
HP iPAQ hx2490C
HP iPAQ hx2790C

Windows Mobile 5:

• English - ENG - (1.03.02.H) -SHIP_HX2000C_1_03_02_H_ENG.zip(30.52 MB)
  
  
• Spanish - SPA - (1.03.02.H) -SHIP_HX2000C_1_03_02_H_SPA.zip(30.21 MB)
  
  

Windows Embedded Handheld 6.5 Classic by Spiaatie:

• English - ENG - (WEH65-01-01-13-ENG)
  
  
  Screenshots:

  
  
  
  You can buy WEH6.5 ROM forHP iPAQ hx2490C and HP iPAQ hx2790C from Spiaatie -> here
  

Post has been editedsnakekvv - 04.01.13, 10:54