Here I will help you to run Linux on our PDAs







To start, you will need

Download all

1.MSCONSOLE.cab(44.74 Kb)

2.Linux.zip(647.94 KB)

3.Linux___iso.zip(49.29 MB)

4.VGAKEY.rar(177.08 KB)

5.w.txt(1.34 KB)

6.q.txt(1.34 KB)

Now perform all of ocherodke

1.Izvlekaem of Linux file and copy it to the \ sdmmc \ Linux \
2.Izvlekaem Fail Linux.iso of Linux - iso.zip in \ sdmmc \ Linux \
3.Ustanavlivaem MSconsole.cab
4. If you have less than Vga - 640x480 then swing prog VirtualDisplay (Here I am to her instruction I can not give)
5. For performance Copy Fail Q.txt to the root \ q.txt
6. For a large number of FPS Copy Fail w.txt to the root \ q.txt
6.Stavim VGAKEY and do as instructed
6-2 climb into Settings and turn VGAKEY SHOW F1-F12
7.Naznachaem any hardware buttons on<Input panel>
8.Povorachivaem screen to landscape orientation
9.Peregruzhaem device
10.Zapuskaem prog CMD (command line - Otobrozhaet everything on PDA and have the opportunity to intervene
11.1 run option, enter "cd sdmmc \ linux \" we press the ENTER, enter "bochs" Hit enter vylaziet itself a program and there are options
11.2 startup option open conductor and run Fail \ sdmmc \ linux \ bochs.exe: D
12. bid embodiments Hit figure 2 and ENTER, enter \ q.txt or \ w.txt We press ENTER
13.Zhmom figure 6 and ENTER
Most likely fly error but you enter Cont and ENTER
14.Vyvalivaetsya black box and a little later on the penguin Hit VGAKEY - F5
15.Vidi he pishit press F2 or F3 or ENTER
16.VNIMANIE again we press on F5 then in Bochs-interface and see the USER button klaviaturku and we press on it there instead NONE enter F3 and hit OK
17.Teper can click on VGAKEY F5 expanding to fill the screen
18.Tam you will see download options Entering "dsl vga = 7xx" and hit ENTERlater we press SPACE when asked.
19.Nu and now wait for it to start
20. When something appears just Hit Enter there anyway to linux kontska. but when I asked that you have a USB mouse skachazhite him not later another window about mouse and there is not but in the third select Ps \ 2myshku
21 Well, after all counterfeit turnip
: thank_you:

If your flash drive is called in another "sdmmc" then you should zalest in config q.txt or w.txt depending on how you start
Everywhere where it is written SDMMC - correct in your name flehi

Post has been editedbasildoom - 23.08.10, 14:43

as well as on your device, this miracle run?

Post has been editednoel89 - 23.08.10, 19:04

Fail to find q.txt or w.txt line ips = 25000000
"Ips = 1000000" = 1mhz - Plano but runs Eternity - it runs 80 minutes
"Ips = 10000000" = 10mhz Pts Pts smoothly and quickly - run 50 minutes
"Ips = 100000000" = 100mhz very quickly loaded but there are lags - run 30 minutes
"Ips = 200000000" = 200mhz vaschsche fast - starts 20 minutes



Post has been editedbasildoom - 23.08.10, 20:50

Working with the file system within the own image? Or sees the whole PDA?

Only work with the image, it is possible to connect a USB and hewing FireFox current that would-USB was Nat
but for this it is necessary to adjust the configuration
but it is still in the CMD load one of the two configs 2 ENTER, q.txt or w.txt ENTER
3 then ENTER

Post has been editedbasildoom - 24.08.10, 10:24

Here are the current still must choose at zagruzkn 16 Bit and the entire image is not much worse

On my HTC touch 2 At first all goes as it should, but when it comes to screen resolution, then there is a problem! When you change the screen 640 * 480 PDA hangs tightly! And the result hadreset! People tell me how else to change the resolution pliz!

Where? It is in thee when it is the window with permissions ???? with options ???

No! After the device is reset to HTC screensaver

dima199 I also hangs: D

'm reccomend ispolzovat this emulsion only at Vga devices otherwise on PDA with qvga may freeze when uploaded supra DIMA199 and xxzz or may hang sho PPC

Post has been editedbasildoom - 25.08.10, 01:01

Eprst !!!!
Get out!
I wrote:

no memory for swap file (1)

As far as I understand is the drive swap / pagefile.

Post has been editedimpuls @ - 25.08.10, 14:36

Impuls @ swap.swp creates a file on the memory card

Starts Bosh Uploaders config q.txt or w.txt, until PUSH 6

PUSH 3

Tsiferki see that before memory
then the bottom uvidesh something about a way to swap the dialed digits 8 is in front of him ....
you enter the name of your swap example: \ sdmmc \ swap - .swp optional
zhmosh enter until you will get out on the initial screen then zhmosh save, enter the name of the config \ q -. txt not necessarily
and then started (entry 6 ENTER) or simply ENTER and voila!

Post has been editedbasildoom - 26.08.10, 16:17

Fine!
But now I have sex penguin appeared (WQVGA), hit f5 - was on the whole screen, but the penguin etat and stait !!!
The picture does not change !!!!!!

time at cha such a small screen is something poke blindly according to the instructions

_{Attention PROGRAM VIRTUAL DISPLAY NOT USE - it can lead to unforeseen POSDEDSTVIYAM
Eg DEATH Soup
HARD reboot SAVE RARE}

Well this is utter nonsense ....

people that I do do as instructed when a black window Bosch opens what that window and it says something about bios there click continue and the black screen as the worth and so should (at the bottom it says sata0 master: 123 atapi-4 cd-rom / dvd-rom)
p.s no penguin I did not have
-----
instead I decided to ... but now I have another problem ... I wqvga screen and penguins except three, I do not see anything .... like me Edit screen without consequences

Post has been editedRobotsyp - 03.09.10, 14:47

Fail to q.txt wherever written sdmmc write their name flash cards

Posted 05-09-2010, 14:34:

Death to hard reboot XD ... I have the dough on a rover pro evo v7 everything is much faster

how quickly work? is it possible to start the program? Does the Internet is supported by vayfay. whether it is possible to attribute one more zero?