FAQ on flashingHTC Raphael
HTC Raphael, HTC Touch Pro, HTC Fuze
Discussion пїЅ | Flashing пїЅ | FAQ | WWE firmware on xda-developers | Firmware list | Firmware review | We do firmware independently | Choosing a stable firmware "for every day" | The choice of radioROM "for every day" | Terms and jargon

The presented material is unofficial, in case of unsuccessful firmware or loss of the device, the Administration does not bear responsibility for the resource! All actions are performed at your own risk!

In the primary collection of information involved respectedsnakekvv .

Rubricator

Found a bug? Have any comments / suggestions? Please writeto me in lichku.

Post has been editedSergey164 - 08.01.12, 19:50

Rubricator

• A brief glossary of basic terms
  
• Installing HardSPL to the factory SPL
  
• ROM firmware
  
• Firmware radioROM
  
• Alternative methods for flashing ROM and radioROM
  
• List of error of the original and modified proshivalschika
  
• Problems and Solutions
  
• How to find out what firmware is currently installed?
  
• How to perform a Hard reset on the GSM version?
  
• How to perform a Hard reset on the CDMA version?
  
• How to enter the Bootloader (Bootloader) mode?
  
• How to flash under Vista?
  
• How to flash under Windows 7?
  
• How to remove the SIM lock?
  
• How to remove Security lock?
  
• How to change the boot image (bootsplash)?
  
• How to install and where to get the desired rilphone.dll?
  
• How to reset the timer duration of the calls?
  
• How to clean flashROM using mtty?
  
• An alternative method of purification flashROM
  
• You can read more about Pagepool?
  
• What you can resize Pagepool?
  
• References to known dishes (Raphael Kitchens)
  
• How about rewriting CDMA device?
  
• As russify hardklaviaturu and Manila in the WWE firmware?
  

Post has been editedtsc - 01.05.10, 14:03

1. A short glossary of key terms

Dictionary characteristics on PDAsavagemessiahzine.com

• Hard reset - Hard restart, at which the device is reloaded with a full erasing all user data. Required for full cleaning / reinstall your operating system.
  
• Soft reset - Soft reset, at which the device reboots retentive. The procedure is similar to turn off and on the power device or momentary battery removal.
  
• Bootloader (Bootloader, mattress) - Boot area with primary driver for the starting apparatus; Electronically controlled devaysa work program on low, hardware (something BIOS type of the computer).
  
• RomUpdateUtility (RUU) - routine-flasher, which is required for reprogramming the device official firmware and run from the PC (modified firmware flasher used for unofficial firmware or radio).
  
• RadioROM (radio, radioROM) - The software part of the firmware responsible for the operation of GSM networks. Comes with official firmware. It can be updated separately from the main firmware.
  
• Firmware (ROM) - it consists of XIP (xip.bin) and IMGFS (imgfs.bin - OEM folder, SYS and registry files and default user) and still something. format firmware * .nb It is a conventional dump (copy of the entire system) with PDA (containing XIP, IMGFS and something else).
  
• Core or XIP - is roughly core windows mobile + key driver.
  
• In folderOEM It is a set of drivers and other software from the manufacturer, to sharpen bare Windu for a specific device. This usually romodely add their packages and programs.
  
• Sys - This folder is actually a naked image of Windows, it is universal for all communicators (NOT devaysozavisima, that this folder can be copied to any firmware that makes romodely when creating firmware with new versions of Windows Mobile).
  
• AKU - Adaptation Kit Update (AKU) - a software package of bug fixes and adding new features to the operating system Microsoft Windows Mobile. Analogue of Service Pack (SP) on Microsoft Windows 2000 / XP / Vista. AKU - subversion of the operating system. It is displayed in the information about the operating system (Settings ->System tab ->Details ->Version tab). The information about the operating system has a parameter Build (Build). The last 3 digits - AKU.
  Separately AKU not downloaded or installed. AKU is embedded in the current firmware.
  
• PagePool - is an area of ​​memory allocated from the operating system and is used for caching information. Increasing size PagePool can achieve faster system response to user actions, decrease - more memory for running applications.
  
• SPL (Secondary Program Loader) - is the primary boot loader (also called bootloader), that it loads Windows Mobile. Also, it is usually integrated flasher. It is stored somewhere in the flash-memory (usually in a separate section, which is not visible in the system).
  
• Hardspl - Modified the boot loader, so you can upload any firmware with any language (for "gray" machines there is a nuance, see. Region lock ).
  
• Security Lock - a software restriction which does not sew RadioROM (radio) from other devices. For radio firmware from Diamond / HD need unlock (razblokirator) is the option (unlock at any given time only for the money).
  
• CID lock (Country ID) - software restriction that contains the operator code (factory) and the country (the device localization). The standard program-flasher checks the CID and CID in the firmware in devayse and allows you to fill in the firmware only when they coincide. Those. CID lock - it belongs devaysa to the country for which it is made.
  
• Region lock - an additional software limitation (in addition to the CID lock), located in the most piercing:
  Q:- Please explain whyHardspl can not bypass regionlok in the "gray" devices?
  A: -Hardspl It allows you to flash any ROM, BUT in the Russian firmware has checked Device ID So that the flash can be, but after the message gets out that rum is not intended for the iron. This check is available only in the Russian version of the firmware, because the gray machines we have a lot, so HTC and came up with this kind of protection method.
  - This is a test device ID, it is in XIP'e, which is whyHardspl can not get around it, in fact he is nothing about it does not know, because are two independent things. Hardspl - a loader, it is when you turn the device loads the kernel (the core of it only knows how to load and transfer control to it), as it already does this check and ID do not match the region returns to the loader control, which displays a screen with napisyu " Your OS ROM is not customized for your hardware "Loading at this stop.
  Again ->only inRUSSIAN firmwareWe began to useRegion lock !!!
  
• SIM lock - soft limit for mobile phone operation within a particular country, the network (including a specific MVNO), or a certain type of SIM-cards. (original text )
  
• PIM (Personal Information Manager) - abbreviation of the link to the software (staff or purchased separately), organizes the work with a list of contacts, tasks, schedule and notes.
  
• mtty - The program of this terminal, which allows the computer to work with the internal memory flashROM devaysa directly through the bootloader. It has a list of commands and is typically used for cleaning flashROM from bad blocks.
  To use recommended in case of frequent spontaneous HR, unsuccessful, etc. pereproshivok.
  The utility is dangerous for inexperienced users, as perhaps spoil yourself devaysa loader and without extreme necessity it is not necessary to use.
  
• Rilphone - a software interface between the actual radio module (radioROM) and operating system (WinMobile).
  All software dostupayutsya to radioROM only through the standard and described in Rilphone.dll function documentation. But exactly how these functions are implemented - it depends on the version radioROM. Those. ideally, each version has its own radimoROM Rilphone.dll. If you use a version mismatch - possible adverse effects (eg do not include binders, eats battery, constant disconnects, all sorts of problems with the GPS).
  

So look around the name of the official firmware file: RUU_Raphael_HTC_RUS_5.05.411.3_Radio_Signed_Raphael_52.58.25.30_1.11.25.01_Ship
The first part of the numbers - the firmware version, the second part - the version of the protocol, the third - the radio version of the module to start flashing her just enough to run when connected via USB to a PC device. Marker official firmware is the wordShip in the file name.
Attention! The designation does not mean Russian RUU firmware identity, Russian firmware have in the title - RUS, and the British - WWE.

Post has been editedtsc - 24.09.10, 12:28

2. Installation HardSPL to the factory SPL

HardSPL stitched once, then you can endlessly change any compatible radios and ROM.
HardSPL designed for GSM devices (HTC Raphael, HTC Touch Pro, HTC Fuze), he is one and universal.

2.1. Computer Requirements:

• Windows XP + must be installed NET Compact Framework version3.5.
  
• If you're running Vista or Windows 7 - try methodfrom hereandfrom hererespectively.
  

2.2. How to install HardSPL:

1. Extract from the device SIM and SD card.
   
2. Download the archiveRaphaelHardSPL_Unsigned_1_90_3.zip(1.32 MB)
   Unpack it into an empty folder on a local drive, not on a network.
   
3. Connect the device to your computer and wait until it is synchronized with ActiveSync'om.
   
4. Run RaphaelHardSPL-Unsigned_190_1_3.exe from the place where you unzipped it.
   
5. Follow the instructions in the RUU (the flashercan't used for firmware ROM or radioROM) ticked off in emerging requests waiting for process termination and restart device (approximately 1.5-2 minutes).
   
6. phone screen should turn black, and then begin a standard firmware process, after which the device restarts.
   
7. Is required to make sure that HardSPL beg properly, it needs to enter into a modebootloader- the inscription should be on the screenSPL-1.90.OliNex.
   

Attention! If there are problems with the claim 6 - Use SSPLManual.exe archive SSPLManual.zip (655.51 KB)

• copy the file to the root of the device and run it from there.
  
• after the screen turn black - run the RUU on the computer and follow the steps in the wizard.
  

2.3. Procedure for returning to the factory SPL (needed for warranty repair)

1. Extract from the device SIM and SD card.
   
2. Sews the appropriate official firmware.
   
3. Run RaphaelHardSPL-Unsigned_190_1_3.exe of HardSPL folder, but do not press anything in the wizard.
   
4. Extract the file from the archive .NBHStockSPL_ForWarrantyOnly_SPL190_1.zip(133.51 KB)
   HardSPL in a folder on the question of replacing the answer in the affirmative.
   
5. Connect your device to your PC and wait until it is synchronized with ActiveSync'om.
   
6. Run the flasher and follow its instructions, firmware flashing process is similar HardSPL.
   
7. At the end of the process in the log modebootloaderand make sure that the SPL version now1.90.0000
   

Alternative link to the whole package HardSPLPackage

Post has been editedsnakekvv - 27.09.10, 08:48

3. Firmware ROM

Attention! Before installing any unofficial firmware or any necessary radioROM flashHardspl.
This applies to both"GRAY"so and"WHITE"devices!
HardSPL stitched once, then you can endlessly change any compatible radios and ROM.

Remember! With any flashing, all your programs are removed and only those included in the firmware build are installed, i.e. After flashing, all your favorite programs must be reinstalled.

Attention! A full backup copy (backup) of the old system cannot be restored on a new firmware !!!

All of the following procedures assume that the PC is running Windows XP and versions of NET Compact Framework3.5.

3.1. Before flashing:

• Charge the battery to at least 60%.
  
• Make a backup of all important data (contacts, mail, messages, meetings, notes, other documents) to return them in a new firmware, for this you can use third-party utilities, for example,SPB Backup, Sprite backup, PIM Backup.
  
• Disable the screen saver on your PC.
  
• Extract from the device SIM and SD card (this recommendation).
  
• If you're running Vista or Windows 7 - try methodfrom hereandfrom hererespectively.
  

3.2. The procedure for firmware "white" machines the official Russian firmware:

1. Download firmware fromofficial siteor fromlist, Put (We save, move, razarhiviruem) It in a clean folder on a local drive "C" ("D", "E", or to whom it is convenient), For example, C: \ myHTC.
   
2. Connect the device to your computer via a USB-cable, preferably to a laptop, because a power failure during the firmware can also kill your communicator.
   
3. Waiting closure aktivsinka synchronization (when the green icon will no longer rotate with arrows).
   
4. Run the .exe firmware file and follow the instructions in the wizard: a computer will proshivalschika dialog box, it always ticked off (ie agree) and click NEXT (below), then start flashing procedure (first device goes into bootloader mode, then firmware) will begin.
   
5. DO NOT DISCONNECT device from the computer until after the flashing process.
   
6. The process takes 15-20 minutes, then restart the device.
   

Note1 : installation Hardspl in this case, optional (but desirable).
Note2 : All devices without HardSPL can flash only official firmware (Resp. RUS for "white", WWE et al. For "gray"). When this flashing ROM and radioROM upgraded.

Remember! Flashing without installationHardsplIt is dangerous and can kill your device !!!

3.3. Firmware order "gray" machines without the official Russian firmware Region Lock:

1. If HardSPL not installed - install.
   
2. Download the firmwarefrom hereand put (We save, move, razarhiviruem) It in a clean folder on a local drive "C" ("D", "E", or to whom it is convenient), For example, C: \ myHTC.
   
3. Connect the device to your computer via a USB-cable, preferably to a laptop, because a power failure during the firmware can also kill your communicator.
   
4. Waiting closure aktivsinka synchronization (when the green icon will no longer rotate with arrows).
   
5. Run the .exe firmware file and follow the instructions in the wizard: a computer will proshivalschika dialog box, it always ticked off (ie agree) and click NEXT (below), then start flashing procedure (first device goes into bootloader mode, then firmware) will begin.
   
6. DO NOT DISCONNECT device from the computer until after the flashing process.
   
7. The process takes 15-20 minutes, then restart the device.
   
8. If desired swing and sews the required version radioROM.
   

Note1 : When this flashing only upgraded ROM
Note2 : Used Region unlocked firmware from a reputable Football on the basis of RUU_Raphael_HTC_RUS_5.05 WITHOUT radioROM.
Note3 : If any problems with the flashing device fails, for its treatment requires an official firmware that came with it initially (ie, the one that was installed on the device when you bought it). The same firmware, you will need to roll back, if you decide to take an official guarantee for repair.
Attention! In no caseNOT sew "gray" machines nerazlochennoy official Russian firmware !!! Cm. Region lock in the glossary.

3.4. The procedure for firmware "white" / "gray" machines of any unofficial firmware:

1. If HardSPL not installed - install.
   
2. Download the desired firmware and put (We save, move, razarhiviruem) It in a clean folder on a local drive "C" ("D", "E", or to whom it is convenient), For example, C: \ myHTC.
   
3. Connect the device to your computer via a USB-cable, preferably to a laptop, because a power failure during the firmware can also kill your communicator.
   
4. Waiting closure aktivsinka synchronization (when the green icon will no longer rotate with arrows).
   
5. Run the .exe firmware file and follow the instructions in the wizard: a computer will proshivalschika dialog box, it always ticked off (ie agree) and click NEXT (below), then start flashing procedure (first device goes into bootloader mode, then firmware) will begin.
   
6. DO NOT DISCONNECT device from the computer until after the flashing process.
   
7. The process takes 15-20 minutes, then restart the device.
   
8. If desired swing and sews the required version radioROM because unofficial firmware does not usually include radioROM.
   

Attention! In no caseNOTsew "gray" machines nerazlochennoy official Russian firmware !!! Cm.Region lockin the glossary.

And finally: in order to avoid possible problems after each flashing (the screen before performing calibration or immediately after the final OS boot) it is strongly recommended that you perform Hard reset.

Post has been editedtsc - 20.03.10, 00:11

4. Firmware radioROM

Attention! Before installing any necessary radioROM flashHardspl.
This applies to both"GRAY"so and"WHITE"devices!
HardSPL stitched once, then you can endlessly change any compatible radios.

4.1. Necessary remarks.

Firmware radioROM does not affect the operating system and does not lead to Hard Reset and data loss, but just in case the pre-make a backup of all important data.
Before flashing radioROM communicator battery must be chargeduntil at least 60% .
RadioROM version can be seen when booting the device, at the time when the bottom right there are three lines with red numerals - the first version of the radio ones. It can also be found in the information on the system settings.
IMPORTANT! Do not try to stitch radioROMy from other devices on Qualcomm MSM7201A platform, for example. Touch Diamond / Touch HD, it can lead to the inability to use GSM device. To enable this firmware on your device is required to carry out the procedureSecurity Unlock .

4.2. The procedure for flashing radioROM:

1. If HardSPL not installed - install.
   
2. Download the desired firmware and put (We save, move, razarhiviruem) It in a clean folder on a local drive "C" ("D", "E", or to whom it is convenient), For example, C: \ myHTC.
   
3. Connect the device to your computer via a USB-cable, preferably to a laptop, because a power failure during the firmware can also kill your communicator.
   
4. Waiting closure aktivsinka synchronization (when the green icon will no longer rotate with arrows).
   
5. Run the .exe firmware file and follow the instructions in the wizard: a computer will proshivalschika dialog box, it always ticked off (ie agree) and click NEXT (below), then start flashing procedure (first device goes into bootloader mode, then firmware) will begin.
   
6. DO NOT DISCONNECT device from the computer until after the flashing process.
   
7. The process takes approximately 10 minutes, then restart the device.
   

Post has been editedtsc - 17.03.10, 12:37

5. Alternative methods for flashing ROM and radioROM

5.1. Firmware from the PC Bootloader mode.

This method is required if the device for whatever reason, can not boot into the operating system (although it can be used in any case).
Protsecc similar to the standard firmware using Activesync, just before connecting the device to a PC you need to enter in bootloader mode.

5.2. Firmware from the memory card.

This method is typically used when unavailability / computer fault (although it can be used in any case) and requires that the root of the memory card image file of the desired firmware.
The order of the firmware:

1. The memory card must be formatted for FAT32.
   
2. Extract the desired firmware, find the file extensionnbh .
   
3. Rename it toRAPHIMG.nbh .
   
4. We place this file in the root of the memory card.
   
5. Instrument in Bootloader Mode.
   
6. Further, the writing on the screen you can press power button to start the process of firmware - Hit. Next on line run that fileRAPHIMG.nbh found and which modules are included in it (- OS, - Radio, -). If the unit immediately returns to the Bootloader mode - the current memory card is not suitable for reprogramming.
   
7. While there is a process, not push any buttons, especially the power button. Runs the progress bar, waiting for completion of the words "willUPDATE SUCCESS ".
   
8. Perform Hard Reset procedure.
   

Note1 : Comfort in the fact that you can copy the file to the memory card out of any operating system, including the phone settings via USB connection mode as a "storage card" (memory card).
Note2 : For this method does not fit all memory cards.
Attention! In no caseNOT sew "gray" machines nerazlochennoy official Russian firmware !!! Cm. Region lock in the glossary.

Post has been editedtsc - 17.03.10, 12:25

6. The list of errors of the original and modified proshivalschika.

• ERROR [202, 204]: CONNECTION
  Improper connection of the device via ActiveSync to your PC. Check the USB cable, make sure the correctness of the connection before running RUU.
  
• ERROR [260]: CONNECTION
  Port to upgrade ROM-and opened by another program. Reboot your mobile device and run RUU again. If you do not help, restart your PC.
  
• ERROR [206]: MEMORY ALLOCATION ERROR [280]: UPDATE ERROR
  If there was this error, close all running programs on your PC and run the flasher again.
  
• ERROR [208]: FILE OPEN, ERROR [210]: FILE READ
  This error notifies you that some files are missing necessary RUU flashers. Download the full package proshivalschika file and try again.
  
• ERROR [212]: FILE CREATE, ERROR [214]: FILE WRITE, ERROR [222, 224]: DEVICE NOT RESPONDING
  These errors occur when a program of remote access CCP collapsed. Check the settings and ActiveSync-connection and restart the RUU.
  
• ERROR [220]: MAIN BATTERY POWER
  The battery of your device is low. Charge the battery before needling at least 60% and try again.
  Note that the device is not able to be charged with updating the radio.
  
• ERROR [238]: FILE READ
  The error may appear because of a broken-ROM image. Download the whole RUU again and try again.
  
• ERROR [240]: FILE OPEN
  ROM image file is not located in the same folder as the flasher - damaged RUU, download it again.
  
• ERROR [242]: INVALID LANGUAGE, ERROR [244]: INVALID MODEL ID ERROR, [294]: INVALID VENDER ID, ERROR [296]: UPGRADE ONLY
  One of the mistakes appear when using RUU, intended for another machine or regional settings are different from the firmware of your PDA. Before flashing RUU checks the identification code of the PDA model and regional settings.
  The solution is simple - download the appropriate firmware for your PDA, or, if you are sure that the firmware is fully compatible with your PDA, install HardSPL.
  
• ERROR [246]: DEVICE NOT RESPONDING
  Flasher can not connect to your PDA. Check the cable connection, otherwise, contact the Service Center.
  
• ERROR [262, 276, 284, 302]: UPDATE ERROR
  The error may occur during the update ROM firmware.
  Using the stylus, restart your PDA and start again flasher.
  Note that in this case, your Pocket PC will not boot, but it will be available in the update mode. We strongly recommend to set the stitching HardSPL.
  
• ERROR [300]: INVALID UPDATE TOOL
  This error indicates that you do not use the appropriate version of RUU proshivalschika.
  
• ERROR [330]: ROM IMAGE ERROR
  The error suggests that you use the wrong RUU ROM flasher and the volume of the image is greater than the amount of flash memory on your KPK.Skachayte another firmware that will fit your model of PDA.
  

Post has been editedtsc - 11.03.10, 18:53

Firmware list

Russian official firmware WM6.1

Attention!!! These firmware can be put only on the officially supplied devices.
Files are searched, those who have the mirror - ask in PMtsc.

RUU_Raphael_HTC_RUS_5.05.411.3_Radio_Sign_Raph_52.58.25.30_1.11.25.01M_Ship
RUU_Raphael_HTC_RUS_CIS_5.05.484.3_Radio_Signed_Raphael_52.58.25.30_1.11.25.01_S
hip

Official firmware WM6.1 for other languages

You can select and downloadfrom hereand part offrom here.

Russian unofficial firmware ( you can bet on any Soup):

WM6.1

• FromJugglahbased Raphael_HTC_RUS_1.90.411.3
  Download
  
• FromFootballbased Raphael_HTC_RUS_5.05.411.3 (identical to the official)
  unlocked (with regionaloklokom removed) official Russian firmware, stable rum for Raphael
  Download
  
• Fromtarkim Crystal ROM 0.3 Build 21051(Selection of users!)
  Version without Manila
  Version of Manila off. firmware
  Version with Rhodium Manila
  
• FromGANZ191188 <a href = "http: // not validssylka.ru / forum / showthread.php? t = 1095 "target =" _ blank ">Phantom_0.1_by_GANZ'_6.1_21054_TF3D21</ a>
  Firmware description
  Download
  

WM6.5

• Fromtuha basWM 6.5 Build 21234 with Rhodium Manill'oy
  Description + links
  
• Fromtuha bas'Spectrum' '_ 6.5_23063_TF3D
  Description + links
  
• FromchaynRelease Manila 2.5 based WM6.5 build 5.2.23060
  Description
  Download
  
• FromGANZ191188WTF_ROM_by_GANZ '' _ 6.5_28005_TF3D21
  Description
  megaupload
  depositfiles
  
• FromGANZ191188WTF ROM v.1.23518 (se) '' _ 6.5_TF3D25
  Description
  
• FromSergeyl
  Discussion
  
• FromradetelAB Edition
  Discussion
  
• FromYDeathYLORD
  Discussion
  
• FromBlasterKey project Zero, WM6.5 Sense 2.5 B & W, HTC Touch Pro / Raphael / T7272
  Discussion
  

RadioROM learned from the official firmware for Raphael



Firmware Android OS

Android Launcher Light ROM
MTM Android Launcher [30.01.10] [v1.0.00.05-beta]

Post has been editedsnakekvv - 25.04.13, 20:40

How to choose radioROM

noval4 Date • 25.8.2009, 22:42
There is one simple truth: the same radio -Can not we all work the same way!
Bo, we all have different operators in different cities with different network coverage, plus there are many different firmware, well, about the set of installed software, I generally keep quiet.
Understand, there is no better radio for all, Best Radio - This is the one that works best from you!
Therefore, the best test of Radio:
1) to make a hard rezet; 2) puts a new radio; 3) experience 1-3 days; 4) XP, and putting the following radio; 5) choose the best at the end of the test.
If you do not want to execute the item (1) with XP, at the same firmware installed without installing new software, recurring items:
2) puts a new radio; 3) experience 1-3 days; 4a) putting the following radio; 5) choose the best at the end of the test.

Post has been editedtsc - 14.03.10, 12:16

How to install and where to get the desired rilphone.dll?


Attention! These actions can lead to Hard Reset, so that the pre-save important data!

How to install в„–1 (Only works on firmware with patched kernel of the OS, are usually all custom firmware)

• Rename the desired rilphone.dll from the list below to rilphone2.dll.
  
• Copy it into the folder / windows device.
  
• In the registry HKLM / Drivers / BuiltIn / RIL specify String Value Dll - rilphone2.dll.
  
• Reload the device.
  
• Reverting to an older dll - in the registry HKLM / Drivers / BuiltIn / RIL specify String Value Dll - rilphone.dll, then reboot the device.
  

How to install в„–2 (Can work and custom, according to unverified information on any off. Firmware)

• Copy the desired .cab file from the list below on the memory card and run.
  
• Reload the device.
  

Post has been editedtsc - 15.03.10, 00:43

How to reset the timer duration of the calls?

Attention! After the procedure will occur Hard Reset, so you first need to make a backup of important data.
So, you need:

1. At the root of the microSD net to put the contents of the archiveRAPHDIAG.rar(87.63 Kb)
   
   
2. Reboot into the mattress and wait for the boot menu of 2 points, press the center. button navigation unit - enter the main menu diagnostic modes.
   
3. Choose Format FAT, will format internal flash memory with zeroing right counters.
   
4. After completion of the reboot - comes standard procedure after a Hard Reset.
   

Post has been editedtsc - 16.03.10, 16:12

As this devayse remove the SIM lock?

SIM unlock currently only availablepaid.
Discussionat XDA-Developers.

Post has been editedtsc - 17.03.10, 12:44

Choosing a stable firmware "for every day"

myrainbow Date • 15.10.2009, 3:29
I want to orient children who join our ranks a little.
What I will say is my personal experience, someone may disagree with me.
I was lucky, throughout the year I have the opportunity to have fun
from the stable operation of my devices. I will not name romodels names,
to whom I am very grateful for this, it will turn out not entirely correct with respect to the others,
no less worthy masters, and that's not the point.


It will be about the device after the firmware, i.e. The flasher on the PC screen congratulated you with a successful update, the device reboots, the USB cable is removed from the socket.

I highly recommend the next step to make the Hard rezet.
There are many opponents of this action, but they can only talk about it meaningless, no one can say that this can not be done (otherwise, it becomes a logical absurdity, imagine: you have installed incompatible software that tightly hung system, and instead of XP and easy rolling a backup need to reflash the difference between the system after the firmware from the system after XP Yes nothing but the contents of the main memory section may vary it may remain the garbage from the previous content:?. firmware transfer process on the device n rezapisyvaet only necessary for its volume area. The system just this debris does not show, but she sees very well. XP greatly increases the chance to get rid of it. After flashing, using a specific tool, you can even get to drive the previous information, in any case, that, that is in the field nezatertoy rum. Once XP is also possible in some cases, but the odds plummet.)
In general, on one side of the scale - "Hard Reset is optional", on the other - "Hard Reset is needed." Weigh yourself.

Further, you must clearly follow the instructions of the author, if any. If the author writes about a specific sequence of actions: any settings, Soft Reset, - be careful, this is necessary.

So, you have done everything that was required of you, and are ready to install third-party software.
I would advise first to make all the system settings for yourself and test the performance of a clean firmware. Press the buttons, open the applications, try to work in them. This will save you from a headache in the future: you will not have to worry in vain, the cause of system errors as the firmware itself, or in the software that you installed.
(Later, when you have a certain experience, you will not need this stage:
in the process of setting up and installing software, you yourself will feel if something goes wrong.)

In general, you twisted, twisted his new shell.
A good option - everything is in order, the device does not slow down, does not freeze, applications open with one touch. Great, we put favorite software.
Bad option - brakes, something does not work, the device freezes. We do another XP.
This can help. If it does not help, choose another firmware.
If you really liked this one - there is another chance: download and flash it again. Sometimes it helps.

In the process of installing the software, the device should not slow down, hang.
If this happens - XP, set it all over again.
If this does not help, the problem is most likely in the firmware, sometimes in the incompatibility of the software,
Try a program that causes problems, replace with an analogue.
If it does not help, choose another firmware, you can not count on the stable operation of the device.

Usually, on the forum, in the branch of your device, all firmware are discussed, their shortcomings, solutions to problems, advantages, details and tricks of use are described. Choosing this or that firmware, be guided by these texts, ask questions yourself if there are no descriptions that interest you. Each section has a FAQ written especially for you.
Good luck.

Post has been editedtsc - 17.03.10, 12:57

How to enter Bootloader mode (Bootloader, mattress)

Simultaneously hold down the "Volume Down" and click briefly with the stylus on the Reset, continue to hold down the "Volume Down", until the display will be multi-colored stripes.

Post has been editedsnakekvv - 27.09.10, 08:36

How to remove this devayse Security lock?

Security unlock currently only availablepaid.
Discussionat XDA-Developers.

Post has been editedtsc - 16.03.10, 10:52

How to clean flashROM using mtty?

If you do not have any problems with the behavior of the device after a firmware upgrade (and not only) - you do not need cleaning .
It goes first to be installedHardspl.

1. Place the device in bootloader mode.
2. The option "Connection Settings" Activesync uncheck "Allow USB connection."
3. Connect the device to your computer (PC), the inscription at the bottom should be changed to Serial to USB.
4. Run on PC exe from the archivemtty1.42.rar(15.68 KB)

- In the "Port" to select USB and press OK.
- In the window, press the Enter keyboard - appears:
CMD>
CMD>set 14 0score as there
We get:
HTCST ITHTCE
---------------------
Then enter:
Cmd>task 29
We get something like this:
Format BINFS start
Fill RSVD information for block 288 to 321
CE start sector = 0x14, total sector of CE and TFAT = 0x14
CE start start block = 321, total block = 1727
ERASE block 1337 FAIL !!!We do not pay attention!
Write 0xFF start page = 0x5040, total page = 0x1AFC0
Format BINFS end

Cmd>
---------------------
Cmd>task 8score as there

5. The device goes into the reboot.
6. Disconnect the device from your PC and convert it into Bootloader.
7. The option "Connection Settings" Activesync check the box "Allow USB connection."
8. Connect the device to your PC and you can flash any firmware.

Note 1: The procedure implies the presence of a PC Windows XP .
Note 2: For the cleaning procedure under Vista / Win7 cm.original text

Post has been editedtsc - 22.03.10, 14:13

You can read more about Pagepool?

paveld Date • 05.11.07 09:54:33

Paging pool (paging buffer hereinafter PP) - is reserved RAM area which is used to store code fragments ready for execution. If PP is turned off, the entire memory device is used for swap, which in turn greatly increases the circulation to the RAM. So inclusion PP, in fact, involves limitation on the amount of memory that can be used for paging. The larger the size of the PP, the greater the buffer RAM is available, and as a result reduces the number of collisions of the memory because more code can be simultaneously taken into the RAM. It is important to find a balance between the PP and the size of the volume accessible to users and programs. The optimal size depends on many factors. Here are some of the highlights:

• Parameters of the OEM software, such as, for example, system drivers.
  
• The total amount of RAM installed on the device.
  
• The speed of the processor.
  
• type flash memory (NAND or NOR).
  

The best way to determine the optimal value for the PP is to experiment with different sizes on your device.
Check performance.
Primarily PP influences the device after download speed SR and launch speed applications, and therefore it is on the basis of these values, conclusions can be drawn about the effective value of the size of the PP. Each option should be measured 3-5 times and use the averaged value. Do not measure the download time for the first few reboots after the firmware, or XP, as it is being carried out additional system initialization.
Translatedpaveld . original article here .

Post has been editedtsc - 14.03.10, 12:14

What you can resize Pagepool?

this utilityPagePool_Changer_v2.21.zip(157.26 KB)

A sourceat XDA-Developers.

Post has been editedtsc - 14.03.10, 12:15

How to find out what firmware is currently installed?

WWE firmware:
You need to go to "Start / Settings / System / Device Information".
ROM Version

RUS firmware:
Need to go to "Start / Settings / System / Device Information"

Post has been editedtsc - 16.03.10, 21:03

References to known dishes (Raphael Kitchens)

1. RUS From Football on the basis of the official Russian firmware WM6.1 RUU_Raphael_HTC_RUS_5.05.411.3 without Region Lock
   depositfiles.com
   rapidshare.com
   In order to collect - Hit Bat on file and will automatically gather all.
   
2. RUS From Sergeyl on WM6.5
   Discussion and links to4htc.ru
   
3. WWE Visual Kitchen WM 6.1 21056/20779
   Discussion and links toXDA-Developers
   
4. WWE Visual Kitchen WM6.5.x
   Discussion and links toXDA-Developers
   
5. WWE Crome ROM WM6.5 Kitchen
   Discussion and links toXDA-Developers
   

Post has been editedtsc - 16.03.10, 10:55