Instructions SPL Upgrade the firmware ROM and RADIO!Important!Firmware Radio (radio) is identical to the firmware ROM (system image)! So look around the name of the official firmware file:
_ATT_Tilt_RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_S
hip
Easily deciphered: first is the appointment of the firmware (for whom: CHTC itself or the operator), then yazykproshivki, then: the first digit - the firmware version, the second part - the version of the protocol, the third - the radio version of the module.
Attention! Marker firmware formality yavyaetsya word
Ship in the file name.
Attention! Designation RUU (! Supra, sic) does not mean Russian firmware identity, Russian firmware have in the title - RUS, and the British - WWE.
So,
official firmware consists of:
- SPL
SPL - it's something in the BIOS similarity to the PC. Responsible for loading the device itself actually re-flash and some interaction between the operating system and device hardware. With all offitsalnymi firmware is appropriate SPL. Just SPL does not allow (see. Above about the CID Lock) to sew the firmware with the wrong ID model / region.
- Splashscreen
Splash - just a picture, which appears early in the boot.
- OS
It is, in fact, the image containing the Windows Mobile.
- Radio
Radio-firmware, RadioROM, radio firmware, radioROM - realtime operating system that controls our telephone module, camera, GPS. (Other PDA can control and others)
Unofficial firmware It consists of at least (and usually) from part comprising
OS . Usually the firmware data is spread in the form of .nbh files (eg
KaiserRom.nbh ). For the firmware file needed .nbh
modified flasher (Sometimes it goes straight to the firmware).
This flasher inter alia
DISABLED Forced HARD-RESET at the end of the firmware. On the one hand it allows to flash Splash Radio or without hard reset. On the other hand if the firmware complete firmware (ie, containing
OS ) After flashing
MUST DO HARD RESET HANDS !!! .
Before flashing: - charge the battery at 100%;
- make a backup (backup of contacts, email, messages, appointments, notes) to return them to the new firmware (a full backup to restore the system to the new firmware can not be !!!), for this purpose, you can use third-party utilities, such as SPB Backup, Sprite Backup and SKTools.
- to put the firmware is not their linguistic affiliation, informal (created by our ROModelami - homemade) or to update the Radio only necessary to carry out the procedure HardSPL both GRAY and WHITE on the device - it is enough to make one time,
- Remember, self-flashing is very dangerous and can kill your device !!!
- if any problems with the flashing device fails, for its treatment requires an official "native" firmware that came with it initially (ie, the one that was installed on the device in the sale). The same firmware, you will need to roll back, if you decide to take an official guarantee for repair.
The procedure for firmware WHITE communicators official firmware: - Downloading ofsaytafirmware.
- Run the firmware file and follow the instructions in the wizard.
- We sew. When flashing upgraded everything:SPL , Splashscreen , OS and Radio .
- If desired swing and sews popular with youradio(Carefully, Inglish, registration required for download)
Firmware The procedure for the white device is not an official firmware (homemade, English and others): - Important! Download and install Hardspl (Unlock our device once!)
note: each time the following flashing the ROM or Radio, Hardspl DO NOT install!
- Run the firmware file and follow the instructions in the wizard.
- Downloading firmware that is like the stitching.
- If desired swing and sews popular with youradio(Carefully, Inglish, registration required for download)
note: for firmware
ANY homemade ROM
is necessary flash
Hardspl Because Many interesting new firmware are made on the basis of the WWE, and then russifitsiruyutsya, and roll back to the official SPL is not a problem (in other words: Before installing all
INFORMAL firmware or radio devices must be white flash HardSPL.
note: all devices (white / gray) without
Hardspl you can flash
ONLY official "native" firmware note: radioROMy (not all, but most are available) can be found hereinafter in Section 4:
Firmware, containing only radioROM The procedure for firmware GRAY communicators: - Important! Download and install Hardspl (Unlock our device, ONE time!)
note: each time the following flashing the ROM or Radio, HardSPL install DO NOT !
- Downloading firmware that is like the stitching.
- If desired swing and sews popular with youradio(Carefully, Inglish, registration required for download)
Standard firmware ROM (system image) and RADIO (radio module radioROM) from the PC: The Microsoft .NET Framework version 2.0 or higher must be installed on the PC.
- Download the firmware and put (save, move, razarhiviruem) it into a clean folder on the "C" local disk ( "D", "E", or to whom it is convenient), for example, C: \ myHTC.
- device (communicator) charged to 100% we connect (connect) to the computer via the USB-cable, preferably to a notebook, as a power failure during the firmware can also kill your device (PDA).
- Waiting closure synchronization aktivsinka (wait until the device is synchronized with ActiveSync'om - when the green icon will no longer rotate with arrows).
- Run the firmware file and follow the wizard's instructions: proshivalschika appears on your computer, it all ticked off (ie agree) dialog box and click NEXT (below), then start flashing procedure (first device goes into bootloader mode, then begin flashing ).
- DO NOT turn off device from the computer until the firmware is complete.
- The process will take about 15-20 minutes, then restart the device.
Regarding Radio firmware (baseband) to the PC: The above described method itself updated and / or flashing Radio (radio firmware is identical to the system firmware image).
IMPORTANT! Do not attempt to flash the radio firmware from Diamond / Raphael / Blackstone / quartz / Jade / topaz / Rhodium Kaiser, it can damage them.
Kaiser's approach
trained Radio Roma from Nike / neon / Polaris.
For any radioROM firmware on your device has to be pre-sewn
Hardspl .
radio module firmware does not affect the operating system and does not lead to Hard Reset (as the radio stitched modified proshivalschikom), but just in case, make a backup of all data.
Before flashing your device radioROM battery must be charged for at least 100%.
Radio version can be seen when booting the device, at the time when the bottom right there are three rows with numbers - the first version of the radio ones. It can also be found in the information on the system settings.
Important: Windows Mobile 6 are 1.27.hh.hh (and they're divided into 2 groups)
Important: for Windows Mobile 6.1 are designed 1.58.hh.hh, 1.59.hh.hh, 1.65.hh.hh, 1.70.hh.hh, 1.71.hh.hh
Important: if the flash that is not appropriate, then cuts off at least the camera and speaker ..
Firmware with PC from under bootloader The same procedure is standard firmware, just before connecting the device to a PC you need to enter in bootloader mode.
Firmware with Flash-card. - Download and unpack the firmware of interest, find the file with the nbh extension.
- Rename toKAISIMG.nbh .
- We put it in the root of the Card (in the "Storage Card" or "Memory Card" folder on the device). The memory card must be formatted in FAT32.
- We simultaneously hold down the "Camera" button and press the cut button for 3 seconds until the bootloader appears (colored stripes on the whole screen - a mattress).
- Further, the writing on the screen you can press power button to start the process of firmware - Hit. Next on line run that fileKAISIMG.nbh found which modules are included in it (- OS, - Radio, -)
- While sewing, we do not press any buttons, especially the power button. A progress bar is running, we are waiting for completion, the inscription "UPDATE SUCCESS" will appear.
- We make hard cuts, as usual by pressing three buttons - left-soft, right soft, rezet.
- Everything!
note: flashing when all your programs are installed and removed, only those that are included in the assembly of the firmware, ie after flashing all of your favorite programs to be installed again.
note: as you know, you no longer need a windows or a connection with ActiveSync, which would beg. You can simply copy the file to a USB flash drive out of any operating system that supports an entry in FAT32 partitions.
Before installing all informal firmware or radio need to sewHardspl .
!!!! Sewn in advance of any action to update the firmware as the unofficial GRAY and WHITE !!!! devicesHardSPLproshivaetsya once, then you can change the firmware on forever. How to install HardSPL (unlock Kaiser) to your device: - We take out the SD & SIM card.
- Download the archive with HardSPLfrom hereor spoilers below, unzip to an empty folder on the PC local disk,no network or on a USB flash drive.
- Connect the device to your computer and wait until it is synchronized with ActiveSync'om.
- copy JumpSPL (turns: 1.56, 1.93 or 1.94) on the device.
- Jump SPL run on the device.
- wait until the display bootloader'a inscription "USB".
- We open the activesync, go to "Connection settings" / Connection Settings "from convinced that the" Allow USB Connections "/" "not selected Allow USB connections.
- chop off the device from the USB port, wait 5 - 20 seconds and connect again.
- KaiserCustomRUU.exe run and thereby begin the firmware HSPL.
- cleduem instructions in RUU (Rom Update Utility) (proshivalschika) ticked off in emerging requests waiting for process termination and restart device (approximately 1.5-2 minutes).
- in order to make sure that HardSPL beg correctly, you need to get into bootloader mode (4-color screen - the mattress) - the screen has to be stitched inscription complies with our HardSPL.
- Everything!
note: If the communicator at Jump SPL start does not go into bootloader mode, or turns white screen, then copy the next version, and repeat from step 1.
available atsavagemessiahzine.comHardSPL, for the complete collection
here To return to the official SPL should: - Download the archive with the original the SPL, extract it to an empty folder on the PC local disk,no network or on a USB flash drive.
- Connect the device to your computer and wait until it is synchronized with ActiveSync'om.
- copy JumpSPL (turns: 1.56, 1.93 or 1.94) on the device
- We take out the SD & SIM card.
- Jump SPL run on the device
- wait until the display bootloader'a inscription "USB"
- We open the activesync, go to "Connection settings" / Connection Settings "from convinced that the" Allow USB Connections "/" "not selected Allow USB connections.
- chop off the device from the USB port, wait 5 - 20 seconds, and connect back
- copy the folder with the file KaiserCustomRUU.exe RUU_signed.nbh containingonly the original SPL
- cleduem instructions in RUU (Rom Update Utility) (proshivalschika) ticked off in emerging requests waiting for process termination and restart device (approximately 1.5-2 minutes).
- in order to make sure that the SPL beg correctly, you need to get into bootloader mode (4-color screen - the mattress) - the screen has to be stitched inscription complies with our SPL.
- Everything!
note: If the communicator at Jump SPL start does not go into bootloader mode, or turns white screen, then copy the next version, and repeat from step 1.
Removal Procedure CID Lock: Download the this kit
for SuperCID.
- Do everything from under WM6.0 with HardSPL1 !!!
- If you have a any of the three HardSPL1, then you next item miss.
- Set the Hard-SPL in the kit.
- Take out the sim card and memory card.
- Connecting the unit to a PC, make sure the ActiveSync icon is green.
- Go to step1 folder and run the flasher. We are waiting for the completion of the firmware. The device reboots.
- Now enter the unit inBootloader
- In ActiveSync, remove the check mark "Allow USB connections".
- in step2 folder run kaiser-supercid.exe
- If everything is correct, then we are waiting for a message: Done, your device should now be superCID and Security Unlocked
- We put the check in ActiveSync "Allow USB connections".
- rebootsBootloader
- Sews radioROM as at step2 "change" radioROM (copy the firmware file to the folder radioROMom in step3)
- All is ready
The procedure for removing the SIM Lock: Download the this kit
for SIM UnLock.
- Do everything from under WM6.0 with HardSPL1 !!!
- If you have a any of the three HardSPL1, then you next item miss.
- Set the Hard-SPL in the kit.
- Take out the sim card and memory card.
- Be sure to installHardspl . This step will protect both the process and unlocks CID .
- Save (remember, write down) versionRadio ROM That is installed on your device. During the unlock will be bathed in a modified radio. Having completed the procedure perezalit original radio for normal operation.
- We connect the apparatus to a computer and waiting for synchronization closure.
- ATarchiveStep1 find daddy and run it from a file KaiserCustomRUU.exe (Of course it is necessary to decompress the archive, rather than run the file directly from it). This step zashot modified radio.
- Change the SIM card in a non-native (another operator card). We wait until the machine is fully loaded and sends it to the mattress (Bootloader, tri-color screen). To do this, you must do Soft Reset button while holding the camera.
6a. In ActiveSync on File->ConnectionSettings remove the checkbox from "Allow USB Connections". On your computer, go to the folder and run Step2 kaiser-simunlocker.exe.
You will see a picture:
=== Kaiser Sim Unlocker В© 2008 by jockyw2001
=== Donations happily accepted, paypal to
[email protected]Your Unlockcode = 12345678
] Done, enter the unlockcode
] And then flash your original radio
Press Enter to exit
Where Your Unlockcode = 12345678 is your unlock code.
After performing this device file restarts in the normal mode automatically and immediately ask you for the unlock code that you already have.
- Download your radiohereand sew it into the machine.
- Everything!!!
comment
you can unlock the device without the "other" simkarty.
all make for unlocking instructions with step simkarty skipping, etc.
after having received and restart PDA, it is necessary to go to the PDA-conductor in windose find Simlock.exe folder and run it.
a window will appear asking you to enter the code, enter it.
further again by unlocking instructions ..
List of bugs as the original and modified proshivalshika
ERROR [202, 204]: CONNECTION
Improper connection of the device via ActiveSync to your PC. Check the USB cable, make sure the correctness of the connection before running RUU.
ERROR [260]: CONNECTION
Port to upgrade ROM-and opened by another program. Reboot your mobile device and run RUU again. If you do not help, restart your PC.
ERROR [206]: MEMORY ALLOCATION ERROR [280]: UPDATE ERROR
If there was this error, close all running programs on your PC and run the flasher again.
ERROR [208]: FILE OPEN, ERROR [210]: FILE READ
This error notifies you that some files are missing necessary RUU flashers. Download the full package proshivalschika file and try again.
ERROR [212]: FILE CREATE, ERROR [214]: FILE WRITE, ERROR [222, 224]: DEVICE NOT RESPONDING
These errors occur when a program of remote access CCP collapsed. Check the settings and ActiveSync-connection and restart the RUU.
ERROR [220]: MAIN BATTERY POWER
The battery of your device is low. Charge the battery before needling at least 60% and try again.
Note that the device is not able to be charged with updating the radio.
ERROR [238]: FILE READ
The error may occur due to a corrupt image RUM-a. Download the whole RUU again and try again.
ERROR [240]: FILE OPEN
ROM image file, and it is not in the same folder as the flasher - damaged RUU, download it again.
ERROR [242]: INVALID LANGUAGE, ERROR [244]: INVALID MODEL ID ERROR, [294]: INVALID VENDER ID, ERROR [296]: UPGRADE ONLY
One of the mistakes appear when using RUU, intended for another machine or regional settings are different from the firmware of your PDA. Before flashing, RUU performs ID code verification PDA model and regional settings.
The solution is simple, download the appropriate firmware for your PDA, or, if you are sure that the firmware is fully compatible with your PDA, install HardSPL.
ERROR [246]: DEVICE NOT RESPONDING
Flasher can not connect to your PDA. Check the cable connection, otherwise, contact the Service Center.
ERROR [262, 276, 284, 302]: UPDATE ERROR
The error may appear during the upgrade ROM-and OS.
Using the stylus, restart your PDA and start again flasher.
Note that in this case, your Pocket PC will not boot, but it will be available in the update mode. We strongly advise before stitching set HardSPL.
ERROR [300]: INVALID UPDATE TOOL
This error indicates that you are using does not match the version of the RUU proshivalschika.
ERROR [330]: ROM IMAGE ERROR
The error suggests that you use the wrong RUU flasher and the amount of the image-ROM and exceeds the amount of flash memory on your KPK.Skachayte another firmware that will fit your model of PDA.
Post has been editeden1gma - 28.09.11, 18:14