Assembly exampleFRX07 from arrrghhh
1) Download the archive with the assembly
2) Extract the contents of the archive and copy it to the root of the memory card
* You can also copy not to the root of the memory card, but to any other folder,But then you need to add the following lines in the startup.txt file:
rel_path = Android / Pro2 either just rel_path = Android
For clarity, an example:

3) In the folderSTARTUPS find the file startup.txt suitable for your particular model. Because we have RHODIUM , then select in the folder RHOD among folders RHOD *** your phone model number (you can see the exact phone model by removing the battery) and take startup.txt and copy to the root of the map (or to the folder in which you extracted the archive)
4) Put the file in the root or folder in which you extracted the archivets-calibration (responsible for calibrating the touchscreen).
There are three options - either use the calibration file from this archive (unzip to the folder (or root) of the memory card), or use your old file (if any), or perform a calibration during the first boot of Android (it appears if there is no file in the folder (or root) of the memory card ts-calibration
5) Optionally, you can also replace the kernel (zImage and modules ) and rootfs . ZImage and modules assemblies as well as a link to the latest builds rootfs .
Unpack the archive with the kernel (zImage and modules ) to the folder with Android renaming the file in advance zImage_xxxxx.xxx.xx just in zImage . Remember to just delete the old file modules-xxxxx.xxx.xx . Archive from rootfs-xxxxxx.img unpack also in the folder with Android renaming it simply in advance rootfs.img .
6) That's it. Start upHaret.exe , and wait for the full download Android . The first download will be long, in subsequent times - much faster.

1) For installationCWM (you can download by reference You will need to split the memory card (it is better to have a capacity of 1GB or more) into 4 sections, namely:
1st section: (primary) FAT32 (sdcard - volume label also matters )
2nd section: EXT2 (system / about 150mb)
3rd section: EXT2 (data / about 250mb)
4th section: EXT2 (cache / about 100mb)
You can break, for example, with a small utility -MiniTool Partition Wizard Home Edition , download
Do not forget that all sections should beprimary sure!
Here is a handy video where everything is clear:Video (Youtube link)
2) Unzip the archivenpkboot-cwm19.zip on a flash drive to a folder npkboot .
3) In the STARTUPS folder, find the filestartup.txt suitable for your particular model. Because we have RHODIUM, then select in the RHOD folder, among the RHOD folders *** the number of your phone model (you can see the exact phone model by removing the battery) and take startup.txt and copy to folder npkboot .
4) To foldernpkboot put file ts-calibration (responsible for calibrating the touchscreen).
There are three options - either use the calibration file from this archive (unzip to the folder (or root) of the memory card), or use your old file (if any), or perform a calibration during the first boot of Android (it appears if there is no file in the folder (or root) of the memory card ts-calibration
5) Optionally, you can also replace the kernel (zImage and modules ) (note that in the folder npkboot it does not exist by default, so you must definitely copy the kernel there!) and rootfs (changes at will). ZImage and modules assemblies as well as a link to the latest builds rootfs .
Unpack the archive with the kernel (zImage and modules ) to folder npkboot renaming the file in advance zImage_xxxxx.xxx.xx just in zImage . Remember to just delete the old file modules-xxxxx.xxx.xx . Archive from rootfs-xxxxxx.img unpack also in the folder npkboot renaming it simply in advance rootfs.img .
6) Download the imageAndroid , for example from here: NeoFROYO V0.1 it will be in the format * .zip , and already !not! unzipping it, you throw right into the root of the flash drive (i.e. not in the folder npkboot ).
7) Download the archive with minimal Google applications (calledgapps ) from here usually in topics with CWM firmware indicates which gapps need to take.
Download the archive in the format* .zip and also drop it right into the root of the flash drive (i.e. not in the folder npkboot ).
8) RunHaret.exe and when the inscription appears Press Volume Down Key to launch CWM Recovery briefly press the volume down key.
Navigation inCWM recovery occurs using the volume up and down keys (up and down, respectively), the accept and end buttons (ok and back, respectively).
On the menuCWM Recovery select item install zip from sdcard >> chooze zip from sdcard , select archive with Android and confirm the installation (it will take about 2-3 minutes).
In the same way, then install the archive withgapps , BUT do not forget to mount (paragraph mounts and storage ) section system again before installation gapps ! In principle, as you install the first archive, you yourself will see a warning, but in English :)
That's it, now select the item in the main menureboot system now . The device will reboot into Windows mobile and now just run it again Haret.exe without going into CWM Recovery (without pressing the volume down button during boot Haret.exe ) The first download will be long, in subsequent times - much faster.
You can also readCWM FAQ .
Not everything there, of course, matches ourCWM Recovery but most of the points are very similar.
Installing various add-ons (Russification, patches, themes and more in the format* .zip ) - Go to CWM Recovery >> install zip from sdcard >> chooze zip from sdcard . Select the desired file format * .zip . Everything (Russification, patches, themes and more in the format * .zip ) put in the root of the flash drive. Install patches, Russification and themes is best before the second full download ( gapps necessarily set during the first boot (i.e. immediately after installing the main archive with firmware) Android .
Note:
Do not use"factory wipe (full reset)" at CWM
Do not use"format sdcard (formatting a flash drive)" at CWM if you do not know what you are doing :)

I do not recommend trying to install Android in Nand on GSM devices with one camera (tilt2, rhod100)! It is noticed that after installing rhodium.nbh the blue fastboot screen does not appear on them.

1. Unpack the contents of the archive6_RHODIMG.NBH_rhod_nand_2012.02.21.zip(28.1 KB)
   to the root of the memory card.
   
2. Copy the archive with the Android assembly to the root of the memory card.
   
3. Download, install and run on BBAndroid SDK manager .
   
4. On the BB, open the command line(Start-All Programs-Accessories-Command Prompt) .
   
5. At the command prompt, type cdC: \ adb .
   
6. Flash the rhodium.nbh file throughBootloader from the device.
   
7. Reboot the phone, a blue screen appearsfastboot .
   
8. We connect the device to the BB through usb and at the command prompt we typefastboot flash recovery recovery.img .
   
9. Wait until Finished appears on the command line and typefastboot boot recovery.img .
   
10. After flashing, a window will appear.CWM Recowery .
    
11. In recovery, using the volume keys and arrows on the keyboard, select and confirm using the call button or Enter key on the keyboard:install zip from sdcard - chooze zip from sdcard .
    
12. Select the desired archive with firmware and clickyes install _ *** . We are waiting for the recovery to finish the firmware.
    
13. After installation is complete, clickreboot now
    That's it, the device boots with the android on board!
    

Files necessary for installation, as well as links to original instructions, are in this topic post HTC Touch Pro2 - Android OS (Post # 11750044)