Keenetic City (KN-1510, KN-1511) - Discussion | [Wifirouter]
Instructions for use KN-1510.pdfStable firmware version2.14.C.0.0-4 from 12/26/2018for KN-1510
Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
ddns
safedns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
ddns
safedns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components
Changes
Installation process and debug mode
1. Download firmware version 2.14.C.0.0-4
2. Installby file upload.
3. Dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.
If after installing 2.14.C.0.0-4 there are problems, you will need to do the following:
1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disabledebug mode.
6. We send debug self-test fileofficial technical support.
2. Installby file upload.
3. Dohardware reset to factory settings.
4. After resetting, connect all devices and check the operation of the router.
If after installing 2.14.C.0.0-4 there are problems, you will need to do the following:
1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disabledebug mode.
6. We send debug self-test fileofficial technical support.
KN-1510_stable_2.14.C.0.0-4.zip(6.39 MB)Mirror:
cloud.mail - v2.04-v2.14 Firmware Keenetic
yandex.disk - v2.04-v2.14 Firmware Keenetic
Good day! This router cuts over the network wi-fi speed more than 2 times (the latest firmware version), tell me what you can do? With routers on YOU
mechtatel77, How do you measure channel speed uplink and downlink in a link partner (device)? Name the model of this device.I am not strong with routers (I didn’t steal before, Internet speed was low, turned on and didn’t look), so I’m not familiar with terms and measurements, I would chew)). Measurement did the usual speed. Tests from the Internet. Of the 70 stated on the wire, it shows almost as much, but on the wifi it cuts more than 2 times (measured on a laptop, tablet, phone) Keenetic City (KN-1510)
Post has been editedmechtatel77 - 05.02.19, 17:08
Post has been editedmechtatel77 - 05.02.19, 17:08
Official beta firmware version2.15.B.0.0-1 of February 11, 2019for KN-1510
Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
ddns
safedns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
ddns
safedns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components
Changes
2.15.B.0.0-1
Supported Models:
Keenetic Giga (KN-1010)
Keenetic Start (KN-1110)
Keenetic 4G (KN-1210)
Keenetic Lite (KN-1310)
Keenetic Omni (KN-1410)
Keenetic City (KN-1510)
Keenetic Air (KN-1610)
Keenetic Extra (KN-1710)
Keenetic Ultra (KN-1810)
Keenetic Viva (KN-1910)
Keenetic DSL (KN-2010)
Keenetic Duo (KN-2110)
Zyxel Keenetic Start II
Zyxel Keenetic Lite III rev.B
Zyxel Keenetic 4G III rev.B
Zyxel Keenetic Giga III
Zyxel Keenetic Ultra II
Zyxel Keenetic Air
Zyxel Keenetic Extra II
Beta version is the official release of updated components that have undergone internal testing and are at the stage of final debugging.
To install the beta version, we recommend updating the Internet Center from mobile devices via the My.Keenetic application or the web configurator.
New features and improvements:
The component "Wi-Fi system controller" has been added to automatically control access points connected via cable;
Implemented support for 802.11v WNM BTM (BSS Transition Management);
Fixed PMK-R1 key exchange problems in FT roaming;
Implemented traffic monitor for arbitrary registered devices;
Implemented ACMEv2 protocol and getting wildcard certificates for KeenDNS domain names;
A form for accepting an End-user License Agreement has been added to the Quick Setup Wizard;
Added support for new Keenetic mobile app;
The automatic connection mode ADSL / VDSL (models KN-2010, KN-2110) is implemented;
Added support for USB modems MTS 872FT, MTS 874FT, MTS 835FT (MF920T) (for models with USB port);
Additional modes: port 0 has been added to the segment settings (for Keenetic Giga III, Ultra II, Giga, Ultra and Viva);
Fixed 802.1p packet transmission with zero VLAN ID;
The implementation of the SMB / CIFS server has been changed from CIFS NQ to Tuxera SMB (for models with USB storage support):
- Support for durable filehandles (launch applications from a network drive, etc.);
- Support master browser function;
- Support for Windows Backup;
- Support for Apple Time Machine.
New features Zyxel Keenetic Plus DECT:
Added support for Panasonic KX-TG7175, Panasonic KX-TG8562, Panasonic KX-PRXA10;
The correct display of numbers with an extension set on CAT-iq 2 handsets is implemented;
Implemented limiting line selection through # in accordance with the rules of dialing;
Fixed problem when re-copying call history or phone book;
Fixed replacing the outgoing call number when the replacement rule contains T;
Fixed line selection through # when dialing one character at a time.
(c)https://help.keenetic.com/
Supported Models:
Keenetic Giga (KN-1010)
Keenetic Start (KN-1110)
Keenetic 4G (KN-1210)
Keenetic Lite (KN-1310)
Keenetic Omni (KN-1410)
Keenetic City (KN-1510)
Keenetic Air (KN-1610)
Keenetic Extra (KN-1710)
Keenetic Ultra (KN-1810)
Keenetic Viva (KN-1910)
Keenetic DSL (KN-2010)
Keenetic Duo (KN-2110)
Zyxel Keenetic Start II
Zyxel Keenetic Lite III rev.B
Zyxel Keenetic 4G III rev.B
Zyxel Keenetic Giga III
Zyxel Keenetic Ultra II
Zyxel Keenetic Air
Zyxel Keenetic Extra II
Beta version is the official release of updated components that have undergone internal testing and are at the stage of final debugging.
To install the beta version, we recommend updating the Internet Center from mobile devices via the My.Keenetic application or the web configurator.
New features and improvements:
The component "Wi-Fi system controller" has been added to automatically control access points connected via cable;
Implemented support for 802.11v WNM BTM (BSS Transition Management);
Fixed PMK-R1 key exchange problems in FT roaming;
Implemented traffic monitor for arbitrary registered devices;
Implemented ACMEv2 protocol and getting wildcard certificates for KeenDNS domain names;
A form for accepting an End-user License Agreement has been added to the Quick Setup Wizard;
Added support for new Keenetic mobile app;
The automatic connection mode ADSL / VDSL (models KN-2010, KN-2110) is implemented;
Added support for USB modems MTS 872FT, MTS 874FT, MTS 835FT (MF920T) (for models with USB port);
Additional modes: port 0 has been added to the segment settings (for Keenetic Giga III, Ultra II, Giga, Ultra and Viva);
Fixed 802.1p packet transmission with zero VLAN ID;
The implementation of the SMB / CIFS server has been changed from CIFS NQ to Tuxera SMB (for models with USB storage support):
- Support for durable filehandles (launch applications from a network drive, etc.);
- Support master browser function;
- Support for Windows Backup;
- Support for Apple Time Machine.
New features Zyxel Keenetic Plus DECT:
Added support for Panasonic KX-TG7175, Panasonic KX-TG8562, Panasonic KX-PRXA10;
The correct display of numbers with an extension set on CAT-iq 2 handsets is implemented;
Implemented limiting line selection through # in accordance with the rules of dialing;
Fixed problem when re-copying call history or phone book;
Fixed replacing the outgoing call number when the replacement rule contains T;
Fixed line selection through # when dialing one character at a time.
(c)https://help.keenetic.com/
Installation process and debug mode
1. Download firmware version 2.15.B.0.0-1
2. Installby file upload.
3. Check the work.
If after installing 2.15.B.0.0-1 there are problems, you will need to do the following:
1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disabledebug mode.
6. We send debug self-test fileofficial technical support.
2. Installby file upload.
3. Check the work.
If after installing 2.15.B.0.0-1 there are problems, you will need to do the following:
1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disabledebug mode.
6. We send debug self-test fileofficial technical support.
KN-1510_beta_2.15.B.0.0-1.zip(6.68 MB)Mirror:
cloud.mail - v2.04-v2.15 (Test, Beta Firmware) All Keenetic
yandex.disk - v2.04-v2.15 (Test, Beta Firmware) All Keenetic
Post has been editedenpa - 12.02.19, 13:26
Stable firmware version2.15.C.0.0-0 dated February 28, 2019for KN-1510
Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
ddns
safedns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
ddns
safedns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components
Changes
2.15.C.0.0-0
New features and improvements:
The component "Wi-Fi System Controller" has been added to automatically control access points connected via cable;
Implemented 802.11v WNM BTM (BSS Transition Management) support for seamless Wi-Fi roaming;
Fixed PMK-R1 key exchange problems in FT roaming;
Implemented traffic monitor for arbitrary registered devices;
Implemented ACMEv2 protocol and getting wildcard certificates for KeenDNS domain names;
A form for accepting an End-user License Agreement has been added to the Quick Setup Wizard;
For DSL (KN-2010) and Duo (KN-2110) models, the ADSL / VDSL automatic connection mode is implemented;
Added support for USB modems MTS 872FT, MTS 874FT, MTS 835FT (MF920T) (for models with USB port);
Additional modes: port 0 has been added to the segment settings (for Keenetic Giga III, Ultra II, Giga, Ultra and Viva);
Fixed 802.1p packet transmission with zero VLAN ID;
Fixed counters for OpenVPN connections;
Fixed possible loss of settings for L2TP / IPsec and Virtual IP;
Added support for new Keenetic mobile application (beta testing);
Added support for Tuxera SMB SMB / CIFS server (beta testing) (for models with USB storage support).
Advantages of Tuxera SMB:
Support for Durable Filehandles (launch applications from a network drive, etc.);
Master Browser function support;
Support for Windows Backup;
Apple Time Machine support.
New features of Keenetic Plus DECT:
Added support for Panasonic KX-TG7175, KX-TG8562, KX-PRXA10, KX-TCD450, KX-TGA810, KX-TCA130, KX-TGC310, KX-TGA661, KX-TCA155, KX-TCA125, KX-TCA120; Gigaset 2000S, 3000C;
The correct display of numbers with an extension set on CAT-iq 2 handsets is implemented;
Implemented limiting line selection through # in accordance with the rules of dialing;
Fixed problem when re-copying call history or phone book;
Fixed replacing the outgoing call number when the replacement rule contains T;
Fixed line selection via # when dialing one character at a time;
Fixed problems with Yealink W52H;
Fixed problems with the work lines without registration;
Fixed errors when editing the number containing the dialing rule;
Fixed errors in reading CAT-iq base settings with 2 handsets;
Fixed display on the handset settings redirect incoming call timeout;
Fixed the phone book with a contact without a last name.
(c)https://help.keenetic.com/
New features and improvements:
The component "Wi-Fi System Controller" has been added to automatically control access points connected via cable;
Implemented 802.11v WNM BTM (BSS Transition Management) support for seamless Wi-Fi roaming;
Fixed PMK-R1 key exchange problems in FT roaming;
Implemented traffic monitor for arbitrary registered devices;
Implemented ACMEv2 protocol and getting wildcard certificates for KeenDNS domain names;
A form for accepting an End-user License Agreement has been added to the Quick Setup Wizard;
For DSL (KN-2010) and Duo (KN-2110) models, the ADSL / VDSL automatic connection mode is implemented;
Added support for USB modems MTS 872FT, MTS 874FT, MTS 835FT (MF920T) (for models with USB port);
Additional modes: port 0 has been added to the segment settings (for Keenetic Giga III, Ultra II, Giga, Ultra and Viva);
Fixed 802.1p packet transmission with zero VLAN ID;
Fixed counters for OpenVPN connections;
Fixed possible loss of settings for L2TP / IPsec and Virtual IP;
Added support for new Keenetic mobile application (beta testing);
Added support for Tuxera SMB SMB / CIFS server (beta testing) (for models with USB storage support).
Advantages of Tuxera SMB:
Support for Durable Filehandles (launch applications from a network drive, etc.);
Master Browser function support;
Support for Windows Backup;
Apple Time Machine support.
New features of Keenetic Plus DECT:
Added support for Panasonic KX-TG7175, KX-TG8562, KX-PRXA10, KX-TCD450, KX-TGA810, KX-TCA130, KX-TGC310, KX-TGA661, KX-TCA155, KX-TCA125, KX-TCA120; Gigaset 2000S, 3000C;
The correct display of numbers with an extension set on CAT-iq 2 handsets is implemented;
Implemented limiting line selection through # in accordance with the rules of dialing;
Fixed problem when re-copying call history or phone book;
Fixed replacing the outgoing call number when the replacement rule contains T;
Fixed line selection via # when dialing one character at a time;
Fixed problems with Yealink W52H;
Fixed problems with the work lines without registration;
Fixed errors when editing the number containing the dialing rule;
Fixed errors in reading CAT-iq base settings with 2 handsets;
Fixed display on the handset settings redirect incoming call timeout;
Fixed the phone book with a contact without a last name.
(c)https://help.keenetic.com/
Installation process and debug mode
1. Download firmware version 2.15.C.0.0-0
2. Installby file upload.
3. Check the work.
If after installing 2.15.C.0.0-0 there are problems, you will need to do the following:
1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disabledebug mode.
6. We send debug self-test fileofficial technical support.
2. Installby file upload.
3. Check the work.
If after installing 2.15.C.0.0-0 there are problems, you will need to do the following:
1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disabledebug mode.
6. We send debug self-test fileofficial technical support.
KN-1510_stable_2.15.C.0.0-0.zip(6.75 MB)Mirror:
cloud.mail - v2.04-v2.15 Firmware Keenetic
yandex.disk - v2.04-v2.15 Firmware Keenetic
I set up this router in my apartment for rent in another city through the My.keenetic program, connecting to it on Wi-Fi and scanning the QR code on the case. Everything happened, managed through the cloud, on the Internet. I went far away, where then I had to break the phone and setting the router and remote control flew. All information about the router I know, photo did, etc. How to restore remote control in the My.keEnetic program? After all, it is impossible to connect to it on Wi-Fi now, it is 1000 km from me.
Good day to all! The question is this. How to harass the City (the main one in the apartment) with the standard MTS DIR 615 router (once it was)? I want to install in another room so as not to lie idle. There, like a bridge somewhere, I read it somehow. Explain on your fingers pliz
Post has been editedSergenqa - 23.03.19, 18:20
Post has been editedSergenqa - 23.03.19, 18:20
Sergenqa, That you need to configure the 615th or access point, if it is connected to the city cable. Or as a repeater, well, or an adapter, if you connect by wifi. In the case of an adapter to the 615th device, it will be possible to connect only by wire. All these modes, he knows how, judging by the description on the site is long.
Post has been edited_mad_ - 23.03.19, 18:58
N-S-B, yes, no-ip
https: //help.keenetic .../articles/360000934780
Well, or you can find another free and drive into the settings - this is possible
+ As noted above, there is also branded keendns - it is also free
https: //help.keenetic .../articles/360000400919
Stable version of KeeneticOS2.15.C.3.0-0 dated 04/01/2019for KN-1510
Component kit
base
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
ddns
safedns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components
easyconfig
config-ap
corewireless
ppp
config-client
pppoe
ydns
config-repeater
ppe
pptp
skydns
dhcpd
l2tp
dot1x
igmp
kabinet
miniupnpd
adguard-dns
cloud
cloudcontrol
pingcheck
trafficcontrol
ddns
safedns
nathelper-ftp
nathelper-pptp
nathelper-rtsp
nathelper-sip
nathelper-h323
components
Changes
2.15.C.3.0-0
Supported Models:
Keenetic Giga (KN-1010)
Keenetic Start (KN-1110)
Keenetic 4G (KN-1210)
Keenetic Lite (KN-1310)
Keenetic Omni (KN-1410)
Keenetic City (KN-1510)
Keenetic Air (KN-1610)
Keenetic Extra (KN-1710)
Keenetic Ultra (KN-1810)
Keenetic Viva (KN-1910)
Keenetic DSL (KN-2010)
Keenetic Duo (KN-2110)
Zyxel Keenetic Start II
Zyxel Keenetic Lite III rev.B
Zyxel Keenetic 4G III rev.B
Zyxel Keenetic Giga III
Zyxel Keenetic Ultra II
Zyxel Keenetic Air
Zyxel Keenetic Extra II
Corrections:
Wi-Fi: fixed a problem with connecting Apple and Samsung Galaxy S10 clients when FT and PMF are on;
MWS: fixed transfer of FT settings over the DS;
Web-interface: fixed bugs;
TSMB: Fixed __ntfs_error errors.
(c)https://help.keenetic.com/
Supported Models:
Keenetic Giga (KN-1010)
Keenetic Start (KN-1110)
Keenetic 4G (KN-1210)
Keenetic Lite (KN-1310)
Keenetic Omni (KN-1410)
Keenetic City (KN-1510)
Keenetic Air (KN-1610)
Keenetic Extra (KN-1710)
Keenetic Ultra (KN-1810)
Keenetic Viva (KN-1910)
Keenetic DSL (KN-2010)
Keenetic Duo (KN-2110)
Zyxel Keenetic Start II
Zyxel Keenetic Lite III rev.B
Zyxel Keenetic 4G III rev.B
Zyxel Keenetic Giga III
Zyxel Keenetic Ultra II
Zyxel Keenetic Air
Zyxel Keenetic Extra II
Corrections:
Wi-Fi: fixed a problem with connecting Apple and Samsung Galaxy S10 clients when FT and PMF are on;
MWS: fixed transfer of FT settings over the DS;
Web-interface: fixed bugs;
TSMB: Fixed __ntfs_error errors.
(c)https://help.keenetic.com/
Installation process and debug mode
1. Download firmware version 2.15.C.3.0-0
2. Installby file upload.
3. Check the work.
If after installing 2.15.C.3.0-0 there are problems, you will need to do the following:
1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disabledebug mode.
6. We send debug self-test fileofficial technical support.
2. Installby file upload.
3. Check the work.
If after installing 2.15.C.3.0-0 there are problems, you will need to do the following:
1. Disconnect all devices from the router, the Eth-cable provider.
2. Turn ondebug mode.
3. We connect back all devices to the router, the Eth-cable of the provider.
4. Reproduce the problem.
5. Disabledebug mode.
6. We send debug self-test fileofficial technical support.
NDM HW ID Decryption
Lite KN-1510-01RU KN-1510
KN-1510_stable_2.15.C.3.0-0.bin.zip(6.78 MB)Mirror:
cloud.mail - v2.04-v2.15 Firmware Keenetic
yandex.disk - v2.04-v2.15 Firmware Keenetic
Post has been editedenpa - 20.05.19, 18:36
Hello. Does anyone give out 300 Mbps over wifi? I get 300 Mbps over the wire from the pranzetka as the provider claims, but through the city on wifi that in 2.4, which is 5 maximum, what I saw - 92 to me is 100 from me. Channels changed, the width of the channels, too. In no way. Are there any additional settings?
dimadav , On the wire, yes, it is written about the limitation of 100 Mbit, but about wifi 300 - 433 Mbit is written on the box?
sl__ , you have in the previous post .... 300 mbps on the wire ... Going into the router turns into ... 100 mbps ... Imho ..©savagemessiahzine.com2005-2021 All rights reserved.
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement
savagemessiahzine.com®- registered trademark.
Terms of Use | Denial of responsibility | Advertising placement