Instructions on how to configure Tftpd64 connection when pouring

The original source picturehttps://pikabu.ru/stor..._c2_na_openwrt_5525675
firmware is better to throw in Tftpd64 folder then can be the path to the firmware does not indicate (Tftpd64 placed in the root of the system drive)
padavan Ready flashing modes onlinaro With her to do nothing, throw in Tftpd64 folder, configure it to connect and sew,
I put onarcher c2v1 The flight is excellent.
1 Download the firmware zip file. ArcherC2V1_tp_recovery.zip
2 Extract from the archive firmware - fileArcherC2V1_tp_recovery.bin
3 Check the MD5 checksum of the extracted firmware2ec19d01d28c7a8c0b5fa66bd7fcc0cc
4 Overwrite bin firmware file in the folder Tftpd64
5 Configure according to the instructions, run on behalf of the administrator Tftpd64 and sew.


ArcherC2V1_tp_recovery.zip(7.41 MB)


Post has been editedmerage - 10.01.19, 13:14

linaro merage, vovan26_,
The problem remains of a previously written it is impossible to fill the firmware via tftp server. Loads 3 percent, and all noticed that the router is rebooted at this point. Nakata firmware programmer because I got tired of being tortured, but you have to solve the problem of why this is happening. I thought firewall conceals the connection is disabled everywhere, no antivirus. It should be the last license win10.

Post has been editedThe_satellite - 06.01.19, 16:22

I sewed on x64 sevens, tens of my specific containers, do not remember exactly, but I think they tftp kosyachit's seven, and I have taken,
her three times sewn different versions of Linaro, I'm not an expert on Flash and more than he tried, I can not prompt, floods, Fast, three seconds and a slider to quickly slips, try the firmware in the tftp folder to put and do not specify the path to it, when pouring herself picked up.

Post has been editedmerage - 06.01.19, 16:54

Does wi-fi work?

I doubt very much that and devays starts :)

vovan26_,
Herzz,
Here I sit with him write this comment, and I do not understand why wi fi did not work? 5G also works.

The_satellite ,
Faced with the same problems oh. Let me know if you will deal

Here is the log

vitaliknv,
The_Satellite,

It had the same problem, helped as follows:

The program tftpd settings, put a checkmark in the Use anticipation window of a value of 1000 and
The tinctures network card in Windows 10, set half-duplex mode
After that I flushed.

P.S. Well, even in the Firewall do for the program tftp rule allowing all.

Thank!!!
Everything worked out!

Post has been editedvitaliknv - 10.01.19, 08:21

Thank you all, it worked out. That's what I understand interface and functionality !!!!! : Thank_you:: yes2:;)



Post has been editedhell766 - 15.01.19, 10:38

Just everything turned out. Thank.
But without the fly in the ointment is not done. It turned out to be that this firmware has earned my old hp printer 1018 is necessary to fence "which the snot" from usb hub and flash drive (((

Post has been editedTerrible - 17.01.19, 18:12

is the theme of self-assembly,PROMETHEUS
can be in the config adjust components to meet specific needs, I do not use a network printer, the assembly made exclusively for dnscrypt connection, because the size of our gadget firmware must be less than 8 megs, long fingered components to fit, could anything you want to disable in the config file. Therefore it is better to collect the firmware for their tasks.

Post has been editedmerage - 17.01.19, 22:31

According to the wiki you want to download the firmware after each turn on the printer. Tp-link have been full-time utility that does this. Firmware is very interesting, but its assembly I not master. I think will have to roll away.

so there is to it firmware with built-in torrent client or not?

People tell me, please. I have a subject. By vay Vayu well-speed cutting, in my opinion - in the line of sight from the router at 5GHz outputs 40-50mb / s at 100 tariff. Do I help the transition to openwrt or padavan? Thank you in advance for your response!

Hello. If anyone has a ready-made assembly of "Padawan", v1, skinki in PM or mail Rwa2012 dog bk.ru I would be very grateful.

Daper, Help

Greetings. Question about port forwarding.
Router Archer C2 (AC750) RU V1 (according to the latest version to the office site for version RU V1.) - I am trying to set up remote control of the print server. The print server (on raspberry) has a fixed inner ip, active ip "associated" with the MAC-address raspberries (binding performed in the router settings). Print server "talks" for wi-fi (port 80). Within the internal network there is no problem to access and manage the print server is done from any computer on the network (there are several) and mobile devices connected by wi-fi to this set. To access the print server from the external network has port forwarding (external ip my network fixed) - indicates a public port, such as 5000 (or 2000, or 3000, or 20, tried different), internal port, where you want to redirect the request of the client program print -server, points 80 and shows the internal ip print server, as the saying goes, "everything by the book." Result- when trying to "reach" from outside to the print server, the connection is not established (error 601, exceeded connection timeout).
Question-router is the problem? (The firewall is disabled, the zone DVZ prescribed ip address of the print server)
I just do not know where to dig, the task is simple, with it when I was a router DIR-300, problems with the Protoss were not there, it worked, and then ambush the blue.

Post has been editedGrivus - 11.02.19, 08:23

Grivus As I tuned Archer C2 to the printer Canon MF232w
EXAMPLE conn. c / o WiFi:
1. Protection / udal.upr
8080 / 255vse
Login to the router willhttp://192.168.0.1:8080
2. Divert / virt.server
Port 9100 | IP-192.168.0.103 | vn.port-9100 | Protocol-TCP or UDP | comp. Inc.
-DMZ off.
-UPnP off.
3. DHCP / rezerv.adr
MAC Address: Printer
IP-address: 192.168.0.103
4. The binding IP and MAC-address-
MAC Address: Printer
IP-address: 192.168.0.103
Configure the printer works too
If conn. c / o the LAN IP (..0.104) and MAC-address changes and all

Post has been editedMjsmart - 11.02.19, 14:45