Noobofakapaniq, The first core is only an initialization script, and the second side of the program (only on the USB flash drive). Dip Slip is if the phone 705

Post has been editedKatochimoto - 13.03.14, 21:18

I understood my mistake. did through the telephone memory

Posted on 03/13/2014, 21:23:

Now another problem. It was 40% of the charge, charged, removed the charging, rebooted, was 60% and now it was charged but percentages do not rise. How to be?

Post has been editedNoobofakapaniq - 13.03.14, 21:22

Noobofakapaniq, Then create on the USB flash drive. Charge up to 100%

Noobofakapaniq, calibrate the battery. How ? Read in the header "Discussions"

Replacing the internal memory with an external (SD card) without the help of third-party programs.
Tested by10f UAE- Works, on other firmware 10 * was not tested.

Before use, be sure to make a backup and save data from SDCard (phone memory) on a computer or flash drive!
Installation is simple: Download the applied file and replace the same file from / System / etc, while monitoring the permissions, they must be exactly the same as the source file.
init.qcom.post_boot.zip(2.18 KB)




Post has been editedKatochimoto - 15.03.14, 07:34

Maybe not here, I do not know where to write. It does not enter Emergency Mode as well in the recovery mode it is impossible to go. What to do?

rl73km, If the phone does not turn on, then the bootloader is killed only in SC.

downloaded the tablet firmware 10 f oae from respectedKatochimoto , through YUKVEB. The bluetooth handed over it to the phone (in the flax root, according to the instructions). I went to CWM, created a backup of the firmware. Made wipe. Run the zip file, the file unloading began, then an android appeared on the back with a red triangle, and the inscriptions:
Error: In 10 _... zip
(Status 7)
Install ABORTED.

I understand that I downloaded the firmware crooked and you need to pull it? Then there is a request, lay out MD5, please compare. The computer is no longer available to me, so you have to do with the tablet, I started pumping the Opera Classic.

While recovered from backup, MD5 file downloaded YUKVEB: F9101B03470C39437AE8A715F8664244

PS However, I looked at MD5 on the archive, which I downloaded, and then handed over the bluetooth. The file was crippled when transmitted via Bluetooth - sent normally, and took crooked. Or vice versa. - TC, YUKVEB is rehabilitated. But the bluetooth ... it is not good.

Post has been editedAleks MI-3 - 16.03.14, 20:09

Aleks MI-3, MD5Checker gives 08EEA1E248ADE680AC47455043B0F9D9.

Hashtab:
CRC32: 1C72D3CF.
MD5: 08EEA1E248ADE680AC47455043B0F9D9.
SHA-1: AE2130CA7FED521BD21B9B5AC68628E5735CFAFA


Post has been editedKatochimoto - 16.03.14, 10:08

Katochmoto, I uncomprisely stepped: the amount of MD5 is present in your post with reference to the Mile.ru cloud! Now looked at the file, the downloaded opera, MD5 coincides. I'll start again. Once again, please accept my apologies: - [

Good day, I have a question, read the whole topic, (maybe not very carefully) but I did not find it. Essence. How to make an application manager from 4.1 to 4.0.3. ??? Well, or just how to make the file manager work from 4.1

Guys, and maybe someone with a firmware cut a standard launcher or suggest how it can be removed.

Open the archive with the firmware META INF folder delete the first line in the UPDATER Script file in unicode. And write back to ask.


Post has been editedKatochimoto - 17.03.14, 08:59

Why when I flash through the KDZ firmware V10TUR_MOD, then it gives an error WPARAM: 100 LPARAM: 4010 What should I do if other firmware ignores?

All overwhelmed I still on the V20C and the phone revived!

Post has been editedDS_RICO - 17.03.14, 19:45

Good day. The question is whether it is possible to roll back with cm 11 on V10F or first on 4.1.2 necessary?

can.

And you can make a hard reset through the computer, otherwise I was covered with a phone after flashing, and only turned on in Emergency mode.
Who knows how to solve it, write out.
LG L7 P705
The firmware put V10E_00

Post has been editedalexlagutin1997. - 21.03.14, 16:09

No, but why, let's put 10 (or better than 10f last assembly) from Ov. Catchchimoto then go to the recovery and make all the wipes after the firmware.

Post has been editedNikRUS_BY - 21.03.14, 18:20

Good evening! In general, for myself came to the conclusion that in the presence of CWM, it is best to have a separate flash drive on (approximately) 4 GB, where to make backups of firmware and flashing .zip ... turned off the device, changed the USB flash drive and please! Plus the fact that if the working flash drive (gigabyte on 32) is killed, the firmware data will remain.

Sorry for the flood - the option is good, but then for extra. Flash. Memory must be made extra. Cord on tel. or somewhere near (it is very relevant for the experiments) :)