Rep: (100)
A very convenient application backup feature has disappeared

There is no such thing in NC as there is much else.



Rep: (100)
No, in general, in any firmware, and I ran a lot of applications, and rebooted, etc., etc.

Attached Image



Rep: (100)
* by_lektor,
Is the swipe from bottom to top from the bottom edge of the display not working?



Rep: (100)
I already did everything, I even reflashed it, maybe I need to turn it on somewhere, there is also no curtain of notifications in applications, it can really turn on somewhere, all the guys help!

Do not use the case with a small window Г  la small window?
I don’t know how on mx3 with such a case, but on mx4pro and the 4.5.x flyme, the panel of running applications does not really work, the volume is not regulated during calls and so on. when the phone is in such a case. On 4.2.8.2 everything works.

-------
on 4.5.4 how many gradations of volume in the player? as well as in 4.5.2 or increased to 4.2.8.2?

Post has been editedtroinoy - 16.07.15, 01:36



Rep: (100)
* Deadked2010,
write to the seller and exchange \ return the phone or kill Bill.

Post has been editedtroinoy - 15.07.15, 02:00



Rep: (100)
and here such question, maybe who knows:
in the summer I ride a bike, the phone is in my shorts pocket, I use a wired headset.
when the phone rings (in my pocket) I pick up the phone from the headset and at the same time (the bell) the phone screen is activated. everything is clear, so everywhere.
but after the call it doesn't matter, I hung up or my interlocutor activated the screen too.
The problem is that the phone through the pocket responds to the body (leg or something else there) and the ridiculous sent SMS starts, it rings by itself and so on.
How to make sure that the screen is not activated after the conversation?
I tried to put the code - do not care, once in general the body was completely blocked.
already worn out, just ridiculous garbage some kind.

I usually took the iPhone with me on the pokatushki - there were no such “bases”, but I donated the iPhone and now I suffer.
once he made a call to the authorities at 4 o'clock in the morning with Banzai shouting - he was leaving the ski slope in the rain !!!

Post has been editedtroinoy - 13.07.15, 14:48



Rep: (100)
Sorry, maybe in the wrong topic! I bought the device from my hands, the seller disappeared, Flyme registered it (maybe). In any case, my registration on the site does not roll, says you need to go under a different ID. How can this threaten me? Can I cross over without a seller? What serious limits will I have in Flyme without ID ....... And anyway, does it make sense then to use the shell or just flash on a bare android and is it possible to do this (will it not make me troubles not registered with Flyme)?

read the cap is not destiny?
one of the methods



Rep: (100)
The question is:
If you flash the CN phone with a repacked bin ->Zip firmware, then roll with the full wipe official 4.2.8.2 I - will the subsequent OTA official updates be installed?

Post has been editedtroinoy - 11.07.15, 13:45



Rep: (100)
* clint7,
Is there a root? regions changed?



Rep: (100)
Kedrs @ 07/10/2015, 16:37*
Was the phone originally HK? Or did you rewrite the firmware?

Yes, everything is simple: the phone was CH, then the CH 4.2.8.2 downloaded from this thread of the forum was flashed into zip CH 4.2.8.2))). after that he started having problems.



Rep: (100)
Sanek3214 @ 07/10/2015, 00:41*
One to one and I, trabla in the firmware turns out.

on the headset?



Rep: (100)
and who uses 4.5.2 (latest version) with a wired headset.
The situation is this:
I call through the headset, block the phone (turn off the display) and after 30 seconds the interlocutor’s voice disappears. If you turn on the display - the sound in 50% appears and appears in 100% there is a switch to the speakerphone.
If you call without a headset - everything is ok.
The headset is 100% working, checked on others - with the display off, the problem is observed at 100%.

I rebooted the modem - the problem remained.
Made a return to the factory settings (wipe) - the problem remained.

On the first version 4.5.2 everything worked OK.

Post has been editedtroinoy - 09.07.15, 17:10



Rep: (100)
* kedrs,
And if you connect to the computer mx3, in the explorer there is a storage folder?
I just have it, after each reboot, and if I remove it, everything that is on the device is erased. at all.

Post has been editedtroinoy - 09.07.15, 00:45



Rep: (100)
daim7610 @ 07/09/2015, 01:25*
in the sense of? What is the 425 modem for 4.5.2 Lolipop, what should have been replaced according to your words? For there are 430 and 435 modems.

According to my words: if the modem is 435, then it will not run on 430.



Rep: (100)
Montikov-d @ 07/09/2015, 01:08*
I have 435

The version is not replaced if it is newer on the device than in the firmware.



Rep: (100)
T1mofon @ 07/09/2015, 00:52*
Well, as for me, the 430 modem, the best one, catches the net and waffle better than the others, if it’s good there, and if not, I’ll sew it, I’d like to know if there is any problem on the candy

430 in flyme 4.5



Rep: (100)
on the last 4.5.2, after 30 seconds, approximately the conversation on the phone begins to disappear and the interrupted call ends for 40-50 seconds. 100% out of 100%.
Wipe from the previous 4.5.2 did not, modem 435.

Posted on 07/08/2015 10:56 PM:

T1mofon @ 07/08/2015, 10:32*
Someone tried to sew modems on 4.5.2?

I. on the first version 4.5.2. There were no problems until it was updated today.



Rep: (100)
I ask to unsubscribe from someone 4.5.2 and there are no problems with authorization to Wi-Fi after reboot - what type of security do you have?

and if possible check with WPA2 PSK

Post has been editedtroinoy - 03.07.15, 16:40



Rep: (100)
* kedrs,
What is your security key type? The case is not WPA2 PSK?



Rep: (100)
Crea @ 07/03/2015, 16:48*
Troinoy, I did not think that you could have a problem with the communication module? I had similar problems on 4.2.8.2, in the SC they stupidly replaced the motherboard and everything is fine.

Yes, I do not think, on 4.2.8.2 everything worked ok.
The problem is that on my 2 devices (32GB and 64GB) all the bugs I identified are identical.
The firmware 4.5.2 itself downloaded from the branch.

Post has been editedtroinoy - 03.07.15, 16:17

Full version

Help     rules

Now: 07/24/19, 05:55