Rep: (4)
correctly suspect :)
Well, if, of course, regular does not suit.
jno @ 07/13/19, 12:44*
jno


The standard one does not want to switch to 3G from E392, and on ZTE modem on 4G Beeline it works.
And how to manage the LED on the standard? WPS flashes a minute and turns off, and the rest how to manage ???

Post has been editedspirtnoff - 13.07.19, 14:54



Rep: (4)
Good day, comrades.
Advise what firmware to use, with minimal knowledge of packages and settings.
There is a TL-MR3020 v3.20 with the latest official firmware + Huawei E392 (I agree - junk) unlocked with connecting Tele2.
Task: stable Internet 4 (more often 3) G with distribution via LAN and WiFi + the ability to control LEDs (GPIO, say instead of the WPS button) to turn on the solid-state relay. SONOFF not to offer.
Thank.
(I suspect - PADAVAN)

Post has been editedspirtnoff - 12.07.19, 22:56



Rep: (4)
Dimon98RUS @ 07/04/19 11:49*
valeramalko,
Tell me, does he playlists hls support or only udp?


Did a long time on the first Giga, supported m3u playlists



Rep: (4)
Mike567 @ 06.30.19, 18:01*
For some reason, in the latest firmware 2.15.C.5.0-0, I stopped entering the USB drive connected from my computer. In the Windows Network settings, all the checkboxes are present, and the settings have not changed. Before that, there were no such problems.

I have the same from the previous firmware.
Most likely it is Windows10 sports, but not for all computers home network.

Post has been editedspirtnoff - 30.06.19, 19:15



Rep: (4)
I ask for help (I used to go to URA myself)

Model and operator: E392 MTS
Firmware Version: 11.833.21.00.14
IMEI: 861230011746576


Thanks, coped

Post has been editedspirtnoff - 21.05.19, 19:17



Rep: (4)
I apologize for the impatience! Overcame only a third of the post ...
Question:
- is it possible to force the first (white) Giga with the NDMS 1.11 firmware to work with the YOTA and HUA392 4G modems each in its USB port constantly connected (alternately, controlling via the Web). Or set 2.04? Just for an Internet in the country, we had to raise the modem and the router, respectively, on a pillar of 8 meters and to switch the providers have to climb every time. One provider is fast but expensive. The other ... on the contrary. The main goal is to blind from what is - without buying anything!
PS: on the ground I can not check, there is no reception. While I use DIR320 (with one USB port) with YOTA or Huawei E320 Tele2, one by one;

Post has been editedspirtnoff - 20.05.19, 23:41



Rep: (4)
Can someone tell me how best to set the focus.
Configured through the author's scripts to send pictures to the soap! But here's the problem: Sony Xperia takes off with a delay due to the focus. In the frame there are backs and nape, or even empty pictures in general without people. I tried to set the mode of the scene of the sport and cars, until the end did not figure out

Post has been editedspirtnoff - 29.04.19, 13:49



Rep: (4)
* bra3and,
Turn on motion sensors and record the audio sensor.
And he will write with short videos while the movement is preserved.

Post has been editedspirtnoff - 29.04.19, 13:05



Rep: (4)
Phtoroplast @ 04/11/19, 00:42*
Interesting - who managed to load the memory of Giga 2 router at least 80% out of 100%? I have a maximum of 20-21% (about 50-51 MB out of 256 MB)

Succeeded!
I connected HDD 2Tb with movies, turned on DLNA for rescanning and started downloading torrent with speed limits.
Download up to 80%, and it would be possible to load SMB: D



Rep: (4)
[/ quot
[email protected], 14:03
decided to hit the provider

Miracles do not happen ...
[/ quote]

No miracles ...
I just brought an old Kinetik-Start and showed the provider - an hour later the channel fell, as it was on Gig2. Technical support boys scratched their turnips, changed something on the line and ... Voila! I just had to come from the sanatorium and not try to solve problems by phone. I say that a couple of years ago there was a similar situation.

Post has been editedspirtnoff - 07.04.19, 16:20



Rep: (4)
Horub @ 04/07/19 13:20*
LOCO @ 04/07/19 12:59
do I have to do a reset using the button?

Personally, I did not do it if the previous firmware worked without any complaints. But still it does not hurt !!!
My problem is that in the postZyXEL / ZyXEL Keenetic II and ZyXEL Keenetic Giga II - Discussion (Post by spirtnoff # 83875428)
decided to hit the provider. Third day - the flight is great !!!

Post has been editedspirtnoff - 07.04.19, 14:04



Rep: (4)
Aramir_ @ 03.29.19, 17:18*
Spirtnoff, transferred with a reset to the factory?

Aramir_ @ 03.29.19, 17:18*
Spirtnoff, transferred with a reset to the factory?

I made a hard reset. Worked less than a day. Internal network lives:
MadiaPlaer + WiFi + 2PC + TV->Dlna + GIGAII->Provider
FileServer + WiFi + 2PC + TV->Dlna2 + GigaI- ^
After restarting GigaII - the Internet is not restored for a long time, if you disconnect the external cable for 10 minutes, then the Internet can work for a day.
One thing is embarrassing that the disconnection, judging by the log, occurs at the time when any of the RSs is connected via wire
Where to crawl?

Post has been editedspirtnoff - 31.03.19, 17:25



Rep: (4)
Aramir_ @ 03.29.19, 17:18*
Spirtnoff, transferred with a reset to the factory?

In the transition from 2.10 to 2.14 - with a reset, to 2.15 - without!
Small note: a similar situation was a couple of years ago at GIGA1. It was enough to not even overload the router, but simplydisconnect external cableabout 10 minutes and ... About the miracle of the Internet worked for almost a day. Then the speed dropped from 100 to 10Mb. By this, I built the provider at attention, and lived quietly for two years. The case is similar, only the speed does not fall, but disconnection from the outside world occurs. Maybe something will be clear from the log.

Attached files

Attached filelog.txt(255.56 KB)



Rep: (4)
Can someone tell me? GIGA2. Sat on firmware 2.10 stable and without rebooting. I switched to 2.15 .... and it so coincided that the provider of the cable flew. The cable seems to be restored, but the router began to periodically fall off the Internet. At the same time, the internal network and services of SMB and DLNA (two 1Tb drives are connected, the power supply unit of the drives and the shared router - 3A) work fine. I tried to put pressure on the provider, but only discovered a strange thing: the Internet can recover itself, but when trying to EXTERNAL CONNECTION to the ROUTER (IP white) via VPN or CLOUD management, the kinetics of the Internet is disconnected.
And the second point: even on the internal network the WEB interface is loaded for a long time. Where to dig?

Post has been editedspirtnoff - 29.03.19, 17:10



Rep: (4)
Paths to the final folder in the face and in the GUI are the same / tmp / mnt / 466 / download

I really have GUI 5.0.1, but everything worked and works great on different firmware!
I wrote the paths like this: / tmp / mnt / 466 / download = // 192.168.1.1/Disk1 / ..., if of course we are talking about a USB drive connected to Giga.



Rep: (4)
Vinman @ 03/10/19, 09:11*
kirandy
while it is working, but the computer does not see the hard drive connected to keenetic 2. I did it according to the instructions from the header, it does not see

And accidentally not Windows10 on your computer, you can not see the drive on SMB?



Rep: (4)
By SMB drives are seen by name, as well as when a direct USB connection to the computer. Does not depend on Latin or Cyri ...
If you look at the DLNA index file, the mount paths are everywhere: / tmp / mnt /F87698723 .... / {file name}
where is F87698723 ... and there is an s / n disk, not its name

Post has been editedspirtnoff - 07.01.19, 20:05



Rep: (4)
Tell me who uses DLNA.
After switching to the latest firmware, smartTV sees two disks connected to the G-II not by name, but by serial number.
You can get used to it, but children are uncomfortable! I tried to disable the HDD, rename and reindex. Did not help.
Where to dig?

Post has been editedspirtnoff - 07.01.19, 19:08



Rep: (4)
understood thanks



Rep: (4)
Who knows what they have for joke on the off site about a choice of 3 OS?

Full version

Help     rules

Now: 07/24/19, 05:52