UrusA ,

I took it off, but still, kz, who knows there the board is just double-sided or multi-layered?

Fee XT-Q7-V10.
Son plugged the left power supply. The result is a corpse.
Opened, on dialing on food kz. Through the laboratory at 5 volts, I began to slowly push the current, I realized up to one ampere, but I did not find anything to warm myself.

If you understand correctly, then you will find the hell scheme for similar pieces of iron. And the one that was laid out above the power supply circuits does not resemble mine. The only thing I could notice was not a hand, but a pyrometer, that the PWM heating is very weak, but not more than 30 degrees.

Still how it does not work out how does + 5V go to USB ...

Did anyone repair such? The prefix has worked properly for more than 6 years and tried all sorts of firmware, and raised it from a software brick. But apparently she didn’t expect that she would get so much pressure on her.

Thanks for any hints.

Read the entire thread, it is not so big.

There are only source codes which should be tried to compile.

joy56 , joy56 ,

No, just flash drives.

The description and cap in the cap are not correct, it has a USB port

Absolutely not clear pattern, once got access to the settings, eventually set up the SSID name, but then the settings again blocked the name of the wafer left which I indicated. After the reset, the SSID name changed to a home one. There are 8 of these routers and it’s not with one that hasn’t been done yet.

If correctly understood through in nvram, you can configure it as you like, uncomfortably wild, but possible.

Maybe someone has a merged lady for the programmer of the firmware where the points are not pale, but you can change it. The firmware that was posted here is sewn up, but the settings still remain not available.

It turned out to start only with OpenWRT with native firmware, the download was hanging at the same place, Left OpenWRT, let's see how it works.

The firmware passes, but in the end the same thing, it hangs in the same place.

DIR-300NRU B7
The web interface does not load during normal loading.

When the reset is clamped and the power is turned on, it turns out to go into the firmware update, the firmware is swallowed, but still it does not load.

Connected via UART.
Hangs on the inscription: "## Transferring control to Linux (at address 802404a0) ..."
Here is the boot log:

U-Boot 1.1.3 (Mar 28 2011 - 12:39:02)

Board: Ralink APSoC DRAM: 32 MB
relocate_code Pointer at: 81fb0000
spi_wait_nsec: 42
spi device id: c2 20 16 c2 20 (2016c220)
find flash: MX25L3205D
raspi_read: from: 30000 len: 1000
*** Warning - bad CRC, using default environment

============================================
Ralink UBoot Version: 3.5.2.0
--------------------------------------------
ASIC 5350_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: SDRAM
DRAM_SIZE: 256 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 32 MBytes
Flash component: SPI Flash
Date: Mar 28 2011 Time: 12: 39: 02
============================================
icache: sets: 256, ways: 4, linesz: 32, total: 32768
dcache: sets: 128, ways: 4, linesz: 32, total: 16384

##### The CPU freq = 360 MHZ ####
estimate memory size = 32 Mbytes
raspi_read: from: 40004 len: 6
.

Please choose the operation:
1: Load system code to SDRAM via TFTP.
2: Load system code then write to Flash via TFTP.
3: Boot system code via Flash (default).
4: Entr boot command line interface.
7: Load Boot Loader code then write to Flash via Serial.
9: Load Boot Loader code then write to Flash via TFTP. 0

3: System Boot system code via Flash.
## Booting image at bc050000 ...
raspi_read: from: 50000 len: 40
. Image Name: DIR_300NRUB7
Created: 2015-10-02 11:43:54 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1036991 Bytes = 1012.7 kB
Load Address: 80000000
Entry Point: 802404a0
raspi_read: from: 50040 len: fd2bf
................ Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 802404a0) ...

I took the firmware from off. site.

The inscription: "Warning - bad CRC, using default environment"
But but I repeat the firmware off. site.

And if you compile them, but do so, to allow changing the settings, and not block them. And in general, how does the provider set up a router, is there no blocking for the subscriber or for them?

I have a login: admin
Password: 2w4f6n8k

According to the link with the firmware, it is the source code that is still necessary to compile them and it seems like they are not homemade ones.


C nvram everything is clear, but it is wildly not convenient

According to the link with the firmware, it is the source code that is still necessary to compile them and it seems like they are not homemade ones.

I have a login: admin
Password: 2w4f6n8k

Subscribe to this topic. I myself got a similar device, tomorrow I will try to reach it via UART, and whether it has CFS (or whatever it is).

In general, for a start, I would like to find his clone.

Post has been editedkotov666 - 07.11.18, 11:35

gamsteb

I stitched exactly the same, like everything plows, but not how I can not start an AdBlock. It seems to work partially, but if you add your lists, does it stop working at all?
But in general, I like everything.

unnever ,
Required converter

Posted 11/01/2018 12:40:

unnever The speed is incorrectly set.

Thank! You were right. Everything was done and earned. Two more DIR-615 K2 are, as well as ru on the house, they would be defeated like that.