peligroso I think that's - order and when let soldering. A motherboard 4-5 TR on Alik - like the already expensive for this nouta. A chip for 1000 you can order.

Yes, VMT tried. By default, it starts with the Intel HD. After you add the program to run with diskretkoy - does not start.

Post has been editedkokokokb - 22.01.20, 10:39

Hello. Laptop Acer 5742 G - Windows 10. I was sitting watching YouTube - nothing foreshadowed. My display blinking - that is, the image disappeared for a few seconds and re-appeared (the image disappears when stopping the cooling fan) and then no longer was involved in about one and a half to two minutes. I rebooted and after a few minutes - this was repeated. Thought on the - loop, matrix, video card. Then remove the driver, and then incorporation diskretki safe mode, did not help. Nout when animation windows immediately fell in bluing, then diagnosis and so the circle. When booting live CD immediately after loading the desktop also started to blink. The BIOS image is not blinking, all the rules. Me - percent, the RAM, unsolder the battery to reset the BIOS. Then I decided to connect the monitor - the image appears on the monitor - loading the BIOS and for a moment in front of windows on the animation will be displayed artifacts such as the fact that in the spoiler, thought the next reboot have time to take a picture, but most of this was not. Loading went on the user's screen and your desktop. Reinstall driver on insertions and diskretku. It puts everything - Manager no device errors. The image at the same time and on a laptop computer and the monitor is. But when running FurMark (launched in the window) - white screen and at the same time shows that 5 fps, and the temperature rises (gt 520m), GPU-Z displays like everything correctly except unknown transistors - a spoiler (picture from the network). But it seems like it's normal. Who has the same diskretka - Write like you. When test SCR 3D - test ends after 5 seconds without any errors (the feeling that it can not initialize the video card).
Turn off your monitor - has launched a new laptop. The bluing no longer falls and live cd boot normally - the image on the laptop is, but diskretka still does not work in fact. I think the replacement vidyahi chip. But the question is - and whether the video memory chips to fly and find / order once the memory for it? Because the last time parsing drew attention to the thermo-memory chips, and that they adhered to a substrate cooling system on the other side (photo example a spoiler - that is on the board 4 places of memory chips - 2 of these empty and place on a cooling substrate where they are not pasted over with black tape Duck's my tape and thermo-swapped -.. on chip tape and scratch thermo suppose that it was originally and therefore chips with the heat not allotted, and how it use up to me to me unknown spot.

Nout bought b / a about a year ago - I was very polluted in terms of cooling, cleaned. Then I sat with an external video card for about six months, then assembled the PC, and that's to take advantage and took noutom started this pandemonium.



Post has been editedkokokokb - 22.01.20, 10:18

Constantly reset PC settings / Account if the sensor or finger is not perfectly clean (hand rubbed with a sensor spray screens - enough for a few minutes, with the phone unlocking from the sensor and a smeary norms operates). But for normal use two correct actuation and crash and all flies third program. Setting reset upon detection of a new fingerprint cut off, but the feeling that it is stupid not work. Versions 1.4.1 and 1.5.2 with the Market. Pro. Android 8.1
Leave a comment in the store. Razrab can answer that. Before each use, wipe the sensor with hands in fear that the settings will be reset - well is currently.
Like decided clogging all available prints in one phone.

Post has been editedkokokokb - 17.01.20, 10:54

evoxx,
2. When the double insertion Photo (flow 8.1) - does not work wi-fi and falls off BT. Flashed vendor 10 - shop just hanging on waiting for the download, reboot. he kind of earned. But he fell off the fingerprint. Unlocks and you can not remove fingerprints - a mark like delete, delete the second when you press, nothing happens and if perezayti in prints, they again both there, add new does not, because the sensor does not work.

You're with a firmware vendor use? Now I try to sew with a ruler. No - the scanner does not start. Or rather now it is wound up, but does not unlock and simply shows the time on a dark screen.

Post has been editedkokokokb - 06.01.20, 14:56

evoxx , Uh, put 10 after the firmware? Or no difference in the vendors? Or you can with 8? Once again, something I try. And with a shortage in the system section for gappsov changes tvrp - where is it? The cleaning sections? They're automatically aligned?

Post has been editedkokokokb - 06.01.20, 13:32

Hmm. Wipes are made. The program is deleted during the installation. Setting too, as usual. I set after flashing 10 by FT. So that problems with the vendor should not be. Wonders.

I stared at 10. All the same, decided to deliver, and ... (Havoc 3)
- Do not install from the App Store (infinite wait downloading). Rebooting does not help.
- It does not work the lock screen. The screen simply goes out.
- Do not operate the lock screen settings. It does not open the lock type string.
- Do not open the line of fingerprints. You can not set the print.
- Do not operate the navigation buttons Home, and Recent Apps. When you click simply vibrate and nothing else. Settings in the Configuration center do not change anything.
- It does not work the synchronization account. Contacts are not updated, although it should sync data.
- A few minutes after the stop to stretch blind quick settings (not fully open).
- Night mode brightness falls to "0".
- When connecting a cable is not working MTP. The connection method can be selected in developer mode but it seems there is not, because when pressed, nothing happens on the assembly room.

Look more and look for something not yet become. I will return to the drain.

It is strange that no one points, or am I a lucky jackpot caught: huh:

I think all of the above must be added to the post with the firmware and indicate that the firmware test.

Post has been editedkokokokb - 06.01.20, 08:18

Memory chip is unlikely that you will find somewhere, and if you find that it is unlikely that when these will be engaged, and expensive (at least need to soldering station soldering the chip). So the choice is either to look at the analysis of the donor or pay on aliexpress. Or to take a new phone.

Nikulyar49 , And here crazy hands? Question about the video card - is the problem with it. Message was originally in the topic set, but was moved here. And I do not regard comments to check on the PC as a real help. I'd done it myself. And so I see no reason to put behind it an A +. But so have you put + for the Old in service.

tukreb Yes, I also think so. I will take a new - though the warranty will be.

AdilKZO , BP has another 550 watts, a new one. But the card still does not work.

AdilKZO In fact of the matter is not a PC. Output can only wait and carry service.

Hello. We have a laptop, exp gdc, geforce 750 ti, BP (old China, foxconn is whether 450W.) The video card was bought at Avito - b / y.
The problem with the video card. It determined perfectly, as she worked. Then became determined through time, several reboots and re-operating rules (no artifacts, distortion, hangs - nothing). And I ceased to be determined exactly. I wound up using it diy egpu program. Still such moment - when the cooler is now spinning as usual, but heard it as if with a "wavy" interruptions at the hearing (after 3 minutes it takes place). If you wait at startup before loading Windows diy egpu 10-15 minutes then the card is determined by the loaded Windows and either hangs over 3 minutes the whole system (only helps with off button) or Manager error code 10. The device drivers are set, but the error does not go away .
Question - what is it - the blade of the chip or the food chain?
Check out the video on a PC can not. Only if in service to carry.

_CKAT_ I have now is tvrp and it is loaded immediately. Try then clamped at 2 - volume [-] and incl. ; volume or [+] and incl. How then should enter after the robot.

Post has been editedkokokokb - 31.08.19, 15:54

_CKAT_ , Then you need more briefly press a button or do not remember exactly what. Try. Then you should see rekaveri menu.

_CKAT_ , Hold down the volume + and on / off. Hold until the Smart turns off and boot options menu. There, select the recovery mode (volume + is scrolling, volume - choice). And in rekaveri select the power off. There is already a key selection on / off button and a string selection - the volume keys. It seems so, I write from memory.

Post has been editedkokokokb - 31.08.19, 07:44

Raalra You can rekaveri through if there is.

Sereebanya , The capacity is taken from the firmware responsible for this one who is collecting it. Yes, even the official. In my firmware shows the 3000, but in fact 3400. For my model, there is a patch for this option as you do not know.

And I versions since 5.x as it did not come. And like a log is created and the vibration is. But the feeling that nothing happens. While the log is written to the label all good in the end. The interface is more Ping-that is, in comparison with 4.12. Phone DEXP z455 android 8.1 magisk 19.3. a feeling that the type of work as a plug, but in fact does nothing. Poorly.
He fell back to 4.12

Post has been editedkokokokb - 20.08.19, 13:56