220 pagesV  1 2 3 4 5 6 > » 

kalipso888
02.03.16, 09:08
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746    +

HomTom HT3 - Firmware
PictureVenso Isprit U50, Ergo A500 Best Dual Sim
Description | Discussion | Purchase | Firmware

Note! Recently, cases of failure of the flash memory of the phone.Read more


Important information!(required reading)
Before flashing the phone, it is recommended to install TWRP and make backup copiesnvram(IMEI),uboot(bootloader, screen operability) andboot(core) on a memory card! In the future, this will greatly facilitate the recovery process in case the phone dies during a flashing.


There are six revisions of this phone:
  • First revision- phones, manufactured until mid-April 2016. Come with pre-installed firmware1.0.5(with viruses in the launcher), or with firmware2.x.x.
  • Second revision (Version 5)- motherboardV5.0.0from March 5, 2016. Phones manufactured after mid-April 2016. Come with pre-installed firmwareV5_1.x.x. Firmware dataare not older, but only have a different label. Ie, for example, firmwareV5_1.0.6for the second revision - analog firmware2.1.2for the first revision. TelephonesErgoandVensorefer to the second revision.
  • Third revision- motherboardV5.0.0from March 5, 2016. It differs from the first and second revision displays. Come with firmwareV5_XP_1.0.1from 07.27.2016.
  • Fourth revision- motherboardV7.0.0from July 1, 2016. Come with firmwareV7_XP_1.0.xfrom September 8/23 (as well as telephonesErgowith firmware from September 28).
  • Fifth revision- motherboardv8.0.0
  • Sixth revision- motherboardv9.0.0from October 26, 2016.

Revision Definition: kernel version only | phone disassembly

If you really want to install the firmware from someone else's revision, then remove the check marks on the filepreloader, bootandubootin the SP Flash Tool. Stitch in Download Only mode.Ignoring these actions may cause the phone to scrape!And do not forget about backup!

Before updating by air is requiredremove root access (complete removal of root).

What is the best firmware, fast and beautiful?
The official update to Android M WILL NOT BE! Read more ...


Drivers and Utilities

Firmware (OS 5.x)
Official firmware
Official firmware is installed via PC usingSP Flash Tool, or using CWM / TWRP Recovery in the case of a separate assembly for them.
1.0.5 / 2.x.x (first revision)

V5_1.0.x (second revision)

V5_XP_1.0.1 (third revision)

V7_XP_1.0.x (fourth revision)


V8_XP_V1.0.x (fifth revision)

V9_XP_V1.0.x (sixth revision)

Firmware to restore the touchscreen (Only for 1st and 2nd revision)
"Universal" stock firmware with System 1GB partition size
Mirror firmware
Instructions for creating a hybrid firmware


Unofficial firmware
Firmware tagged[Backup]stitched onthisinstructions.
If autofocus does not work
Based on cyanogenmod
Installing CM-firmware for TWRP
First we do wipes:
  • Dalvik / ART Cache
  • Cache
  • System
  • Data

Only after that install the firmware.

If you do not see the SIM card / IMEI after the CM firmware
Try the following options:
  • Turn off the phone for two minutes with jerking the battery, and then turn on;
  • Make aFormat Data/Format Datain TWRP;
  • Sew modem (spoiler"Miscellanea").


Firmware archive

Single firmware
For CWM / TWRP

For SP_Flashtool

Custom firmware archive



Firmware (OS 6.0)

Firmware (OS 7.x)

Recovery / Kernels

Instructions

Modifications

miscellanea

Survey Screenshots
Attached Image

Attached Image

Topics Curator roma392

Post has been editedroma392 - 18.04.19, 21:33
Reason for editing: Mirror for firmware V8_XP_1.0.5
Forum: HOMTOM · View message: #47588453 · Replies: 8581 · Views: 1688952

kalipso888
11.02.16, 12:45
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746    +

Kalipso888 @ 11.02.2016, 12:11*
Getting Root through Recover

Before any manipulations with smart, you need to make a bakap.
Getting root rights through stock recovery.
Download fileAttached fileupdate-root-HT3.zip(4.82 MB)

Without unpacking and changing, we throw in the root of the flash drive.It is a flash drive and the memory of the phone otherwise it will not work.

��� ����� � �������� download

- because Smart is not in the hands of this assumption, by analogy with another smart, also Nom NT.
Turn off the phone, hold down the button"on"and"volume +"before the appearance of a choice of items, we chooserecovery<button"volume +"confirm the selection by pressing"volume -" ,
A robot android appears and the inscription"no team"we press the button"on"and briefly press"volume +". go to the recovery, select the buttons"volume +"or"volume -" apply update from sdcard, select our file and confirm with the button"on", after performing the action choosereboot system now.

And if Root is received!
To remove root rights remove Super Su
And then when you upgrade, you will not get a brick !!!

Picture


Post has been editedroma392 - 29.03.19, 20:21
Reason for editing: Replaced broken link to file


--------------------
Do not say if it does not change the silence for the better.
Forum:HOMTOM· View message:#47021851· Replies:8581· Views:1688952

kalipso888
04.03.16, 12:05
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

Put DU Speed ​​Booster. I like. It monitors the accumulation of garbage in the system, loading the system with unnecessary applications, the programs that climb into the Internet and much more useful .. Itself does nothing without the permission of the user.
Instructions for collecting statistics of energy consumption during sleep of a smartphone:
Power consumption (autonomy) Galaxy S IV (Post tester99 # 25260680)
Utility to monitor battery discharge when the phone is idle.
Attached fileBetterBatteryStats_xdaedition_2.2.0.0B5.apk(3.33 MB)

Deep Sleep Battery Saver did not go, lost a deep sleep.
In the process statistics, we see what eats acb, freeze, delete, disable (optional) Disable autostart of all unnecessary.
В® Disable Service (Post zgenia44 # 20467881)
Short description:
Enable and disable services.
Lithium Batteries - Operating Rules

Picture


Post has been editedroma392 - 16.05.18, 18:47
Reason for editing: In the header


--------------------
Do not say if it does not change the silence for the better.
Forum:HOMTOM· View message:#47651462· Replies:6070· Views:1148382

kalipso888
09.02.16, 13:06
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

How to put a melody on contact

Picture


Post has been editedroma392 - 16.05.18, 18:44
Reason for editing: in the header


--------------------
Do not say if it does not change the silence for the better.
Forum:HOMTOM· View message:#46960820· Replies:6070· Views:1148382

kalipso888
11.02.16, 15:08
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

Attached Image

5 practical tipsfor use of lithium-ion batteries.
NeoStalker @ 02.11.2016, 14:56*
Do not say nonsense. I installed it from the phone's memory, WITHOUT a flash drive in the device.

This nonsense tested on another similar smart did not work from the memory of a smart.
Kinggut works on many smarts checked if only for Android 5.1.1. have not yet updated the program.

Picture


Post has been editedroma392 - 16.05.18, 18:42
Reason for editing: In the header


--------------------
Do not say if it does not change the silence for the better.
Forum:HOMTOM· View message:#47025699· Replies:6070· Views:1148382

kalipso888
08.03.16, 04:44
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

Instructions for the recovery of flew IMEI-codes

1.Rewrite IMEI-codes on a separate sheet (they are written under the phone's batteries or on the box);
2.Go to the Engineering menu of the smartphone (using the combination * # * # 3646633 # * # *);
3.Looking for CDS Information =>Radio Information =>Phone 1. In the line after AT + we write E. There will be a choice of AT + EGMR = 1.7, "" and AT + EGMR = 1.10, "";
4.First select AT + EGMR = 1.7, "". In quotes, we write your first IMEI code (you should get AT + EGMR = 1.7, "867312665444899" - something like this). Under the line click on the "SEND AT COMMAND";
5.Below you will see the inscription "AT command is Sent";
6.Then, similarly, we enter the second IMEI code in quotes, but after AT + EGMR = 1.10, "";
7.Again, click "SEND AT COMMAND", see below again "AT command is Sent".
8.Restart the phone and it works! You can check the availability of IMEI-codes using the combination * # 06 #;

P.S .: For those who get the error "This command is not allowed in UserBuild" after sending the command:Put a space after the plus! That is, AT + EGMR = 1.7, "your IMEI"

As I checked that after the IMEI was restored as described above, the codes no longer fly off:
  • First time. Made a reset to the factory settings from the smartphone - IMEI in place;
  • Second time. I made a reset from Recovery with all the wipes - also IMEI in place;
If you demolish the "system" section in Recovery, then I see no point - the firmware will fly off. It is better then just to flash, but then IMEI will not fly off.
If suddenly something goes wrong, then there is alwaysThe program for installing IMEI + Videoon this topic.MauiMETA (Post Digins # 41671213)

Picture


Post has been editedroma392 - 16.05.18, 18:40
Reason for editing: In the header


--------------------
Do not say if it does not change the silence for the better.
Forum:HOMTOM· View message:#47751276· Replies:6070· Views:1148382

kalipso888
07.12.15, 19:46
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

HomTom HT6 - Firmware
PictureHOMTOM HT6
Description | Discussion | Purchase | Firmware

Important information!
Need todeleteRoot rightsSo as not to get a brick when updating the firmware.


Drivers and Utilities

Firmware

Instructions

Recovery

miscellanea

Firmware screenshots
]
Attached Image
Attached Image
Attached Image
Attached Image



There is no curator in the subject. If there is a user in the subject who wants to become a Curator and the correspondingRequirements for candidates, he can apply in the topicI want to be curator(after having studied the topic header and all materials for curators).
Prior to the appointment of the curator, on filling caps, please contactmoderatorssection through a buttonPictureunder the messages to which you want to add links.


Post has been editedCusco - 04.02.18, 19:17
Reason for editing: Official firmware R17
Forum: HOMTOM · View message: #45117185 · Replies: 3234 · Views: 593451

kalipso888
28.04.16, 11:50
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746    +

Infocus M560 - Firmware
PictureInfocus m560, V5, m808 (m808i)
Description � |Discussion | Purchase | power usage | Firmware

Drivers and Utilities

Firmware

Instructions

Recovery

miscellanea


There is no curator in the subject. For filling caps, please contactmoderatorssection through a buttonPictureunder the messages to which you want to add links.

Post has been editedolegusss - 25.12.17, 15:04
Reason for editing: edit
Forum: Other brands · View message: #49220794 · Replies: 2885 · Views: 380851

kalipso888
24.03.16, 12:03
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746    +

How to use SP_Flash_Tool (How to flash a phone)

- UnpackFlashtoolsto the root of the diskWITH:and runFlash_tool.exe
- Select a scatter fileAndroid_scatter_emmc.txtin firmware
Attached Image

- Wait for files to be added to the FlashTool interface
Attached Image

- Select optionDownLoad OnlyorFirmware upgrade, if you update the same firmware to the latest version.
- Turn off the smartphone.
- PressF9orDownload buttonin the case of a new firmware orFirmware->Upgradefor update.
- Then connect smart to computer via USB
- The process will start and the red progress bar will turn to purple, then yellow.
Attached Image

- The green circle is the final. Close the final window, close FlashTool.
Attached Image

- You can disconnect the smartphone from the computer and after 0.5-1 minutes include it in the download.

CWM firmware
1. Download the archive with the firmware from the header.
2. Connect the phone to the computer via USB.
3. We transfer the zip archive with the firmware and zip with the Google App (if they are not sewn into the firmware) in the memory of the phone or flash drive.
4. Go to the recovery. The control is quite simple, up or down is carried out with a volume rocker (+ and -, respectively), the item is selected with the on / off button.
5. In the recovery, select the wipe reset point of everything before flashing it.
Attention! This action will erase all your personal files, reset all settings.
I recommend everything you need in advance to transfer to the computer!
6. After successful wipes, select install zip
Attached Image

7. Choose Choose Zip from / sdcard
8. At the bottom will be the archive name with the firmware.
9. It turns out a new window that asks to confirm your action! choose Yes - Install
10. Wait until the firmware is installed, then select Reboot Phone
The firmware has been installed and the firmware icon will appear on your screen ... Wait another 5 minutes until the firmware is fully installed on the phone.

Posted on 03/24/2016 12:03 PM:

We are updating the update through SP_Flash without losing your data.
- For this we need.
1. Installed on the PC drivers. (there is a hat)
2. SP_Flash tools flasher downloaded to the root of the disk (available in the header)
3. Firmware, the same folder should be in the root of the disk. (there is a hat)
- Firmware.
1. Open the SP FT flasher, it will ask you to select the scatter file (it is located in the folder with the firmware)
Attached Image

2. After the scatter file is selected, all the checkboxes will be set automatically. We need to select download only and uncheck.USERDATAandCACHE
Attached Image

3. Click the Download button.
4. Turn off the smartphone (I recommend to distort the battery after turning it off)
5. Connect to PC. We are waiting for the end.
All is ready. User data saved.

Picture


Post has been editedroma392 - 10.10.17, 22:05
Reason for editing: In the header


--------------------
Do not say if it does not change the silence for the better.
Forum:HOMTOM· View message:#48241346· Replies:8581· Views:1688952

kalipso888
27.03.16, 14:37
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

How to disable digital signature verification drivers in Windows 10

Manual installation of the ADB driver
Option 2 - find a computer with Windows XP and not suffer.
Installing an unsigned driver in Windows 8

Posted on 03/27/2016, 2:34 PM:

Decision if ADB does not see the device
launch the device manager - find on the top of the Android Phone and select the Android Composite ADB Interface, right-click and select the Properties tab, then select the Details tab and select the ID equipment tab and copy the last line

Next, open My Computer - Local Disk - Users - (choose your username) -
Next, open the .android folder. There should be an adb_usb.ini file, if not, create it manually, then open this file and paste our line that we copied into the hardware ID, for example:
USB \ VID_0E8D & PID_201D & MI_01
and edit it by writing 0xUSB \ VID_0E8D & PID_201D & MI_01 (leaving only what is selected and deleting the rest) will turn out like this 0x0E8D, save this file and reboot the computer, and then turn on USB debugging on our smartphone and connect to the computer and everything will work

Picture


Post has been editedroma392 - 10.10.17, 22:05
Reason for editing: In the header


--------------------
Do not say if it does not change the silence for the better.
Forum:HOMTOM· View message:#48330549· Replies:8581· Views:1688952

kalipso888
24.03.16, 11:49
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

BOBAH-C @ 03.24.2016, 10:49*
In the cap, only the link to TWRP itself, and how to flash it is not described ...

Experience installing TWRP Recovery
To begin with, the flash driver installed the program, downloaded the archive already with the drivers.
Right here.
Installed drivers for XP system.
To install TWRP, we will need the scater files and TWRP itself.
Next, go to the settings item - About phone - Build number. Tap on the build number several times and become a developer.
4) Go to Settings - For Developers and turn on "USB Debugging", as well as turn on the factory unlock item.
Turn off the phone. The cable from the computer is not connected.
(If you do not have a laptop and a system unit, then the cable is recommended to be installed from the back of it where the ports are right on the motherboard)
Now open the program for the SPFT firmware (SP_Flash_Tool)
Select the Scatter-loading item and specify the path to our unpacked archive Stock_Files 2.rar
And choose the file _Android_scatter.txt
The checkboxes themselves will be set automatically. It will look like this.
Attached Image

Now you need to click ongreen arrowwith the inscription Download and connect the phone cable.
If you just plug in and wait, then maybe nothing will happen.In addition to error 5054 or 2005.
And if you hold down the volume button +, then the red bar will run, and behind it will be a yellow one and at the end there will be a small square with a yellow circle with the word Download ok and a check mark.
This means everything has been established. Now we go in rekoveri.
To do this, hold down the volume + button and the power button, until the selection of items appears, select recovery in them<With the "volume +" button, confirm the selection by pressing "volume -".
And we get into TWRP recovery.
The whole process in pictures:
Attached ImageAttached ImageAttached ImageAttached ImageAttached ImageAttached ImageAttached Image


In more detail and in pictures heresimilar topic.

Posted on 03/24/2016 11:49:

Recommendations for connecting the device for firmware
if you have problems


It can help both individually and in aggregate:
remove all old phone drivers using USBDeview, you can also other usb drivers that may interfere;
install drivers from the header;
overload Windows, sometimes helps to safe mode;
connect any antivirals, brandmauery and other Windows defenders;
The battery MUST BE charged at least 50%;
connect after pressing a button in the USB flash drive (if you just plug in, without or before the USB flash drive command, after a while the device may exit the mode and continue downloading);
machine off;
connect with a straight forward cable;
connect without any adapters \ extension cords and hubs;
connect in the back on the computer to the port on the mother;
Connect preferably to USB 2.0 ports, with 3.0 there may be problems;
analyze the flashtool log (usually C: \ ProgramData \ SP_FT_Logs \ "Date Folder" \ SP_FLASH_TOOL.log)
try \ change another version of SP_FlashTool (3.x<=>5.x);
if all else fails, try on another computer.

Picture


Post has been editedroma392 - 10.10.17, 22:04
Reason for editing: In the header.


--------------------
Do not say if it does not change the silence for the better.
Forum:HOMTOM· View message:#48240880· Replies:8581· Views:1688952

kalipso888
11.02.16, 12:11
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

3axap85 @ 11.02.2016, 09:31*
How to get root?

Getting Rootthrough rekoveri (custom)Attached fileBETA-SuperSU-v2.52.zip(3.83 MB)

SuperSU - advanced access control for superuser rights to applications on the device that need root.
All versions above 2.52 are experimental and designed for Android 6.0+ and CM13!
Attached filePRO-SuperSU-v2.67.zip(7.56 MB)

Or from a computer through Kingroot programs for example.
KingoRoot (Post by maksnogin # 40791412)

Picture


Post has been editedroma392 - 10.10.17, 22:04
Reason for editing: In the header


--------------------
Do not say if it does not change the silence for the better.
Forum:HOMTOM· View message:#47020858· Replies:8581· Views:1688952

kalipso888
05.04.16, 13:35
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

2 pcs. batteries for 496 r[W002] 3.7 V, 502431, Polymer Li-Ion / Li-Ion battery for smart watches
Picture


Post has been editeddfgigger - 07.09.17, 07:28
Reason for editing: "Proshtampoval", that information is added to the header


--------------------
Do not say if it does not change the silence for the better.
Forum:Smart watch· View message:#48591689· Replies:9533· Views:2981020

kalipso888
10.03.16, 01:22
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

Instructions for those who have lost their IMEI overhaul, but at the same time at least once attached to a Google account on their smartphone:
1. We pass on the linkhttps://www.google.com/dashboard/?hl=en
2. Deploy Android - Devices.
3. We see the name of the smartphone model, the last activity date and IMEI for the first SIM card. Things are easy - calculate the second IMEI
4. To calculate the second IMEI, follow the link -http://www.imei.info/calcand in the field enter the first IMEI, in the field enter 14 digits, the 15th digit will be in a separate field, this field shows the checksum. That is, 14 digits in the first field + 15th digit in the second field = your first IMEI. How to calculate the second IMEI? To do this, change the 14th digit in the first field to +1. For example, if the 14th digit was 6, change it to 7. The second field will be updated, it will show the new digit. As a result, we combine 14 numbers from the first field with a number from the second field and we get the second IMEI for your phone.
Picture


Post has been editedbecause.lyolya - 17.07.17, 19:36
Reason for editing: Raised in the topic header


--------------------
Do not say if it does not change the silence for the better.
Forum:Doogee· View message:#47808601· Replies:8814· Views:1872117

kalipso888
09.03.16, 19:55
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

Instructions for the recovery of flew IMEI-codes

1.Rewrite IMEI-codes on a separate sheet (they are written under the phone's batteries or on the box);
2.Go to the Engineering menu of the smartphone (using the combination * # * # 3646633 # * # *);
3.Looking for CDS Information =>Radio Information =>Phone 1. In the line after AT + we write E. There will be a choice of AT + EGMR = 1.7, "" and AT + EGMR = 1.10, "";
4.First select AT + EGMR = 1.7, "". In quotes, we write your first IMEI code (you should get AT + EGMR = 1.7, "867312665444899" - something like this). Under the line click on the "SEND AT COMMAND";
5.Below you will see the inscription "AT command is Sent";
6.Then, similarly, we enter the second IMEI code in quotes, but after AT + EGMR = 1.10, "";
7.Again, click "SEND AT COMMAND", see below again "AT command is Sent".
8.Restart the phone and it works! You can check the availability of IMEI-codes using the combination * # 06 #;

P.S .: For those who get the error "This command is not allowed in UserBuild" after sending the command:Put a space after the plus! That is, AT + EGMR = 1.7, "your IMEI"

As I checked that after the IMEI was restored as described above, the codes no longer fly off:
  • First time. Made a reset to the factory settings from the smartphone - IMEI in place;
  • Second time. I made a reset from Recovery with all the wipes - also IMEI in place;
If you demolish the "system" section in Recovery, then I see no point - the firmware will fly off. It is better then just to flash, but then IMEI will not fly off.
If suddenly something goes wrong, then there is alwaysThe program for installing IMEI + Videoon this topic.MauiMETA (Post Digins # 41671213)
Picture


Post has been editedbecause.lyolya - 17.07.17, 19:36
Reason for editing: Raised in the topic header


--------------------
Do not say if it does not change the silence for the better.
Forum:Doogee· View message:#47799305· Replies:8814· Views:1872117

kalipso888
29.07.15, 13:35
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

DiscussionHOMTOM HT6
PictureHOMTOM HT6
Description | Discussion | Purchase | Firmware
  • Before asking a question, look Android OS FAQandGlossary. Respect your and other people's time.
  • To discuss and search for third-party programs / games, use the following sections: Programs and Games.
  • To compare the device with competitors and on the choice of devices, please contact: Selection and Comparison.
  • The available amount of RAM and memory for installing applications is discussed in the topic: How much memory is in your machine?
  • The results of performance tests of Android devices, see the topic: Benchmark
  • Before posting photos, read the topic Working with Images on the forum
  • Messages that are not related to the topic of discussion (offtopic) are deleted without warning.
Photo Homtom HT6
Attached ImageAttached Image
Additional photo
Attached ImageAttached ImageAttached ImageAttached ImageAttached ImageAttached Image
Attached ImageAttached ImageAttached Image
About company
HOMTOM is a new subbrandfrom companyDoogeefor phones with a large battery. The brandDOOGEECreated in March 2013 for the development, production and service of mobile devices. Compared to other manufacturers, DOOGEE stands out for its excellent product quality and low price. Brand DOOGEEowned by KVD International Group, leading its history since 2002. KVD is headquartered in Hong Kong, and its own manufacturing facilities are in Shenzhen Province, China. The company produces and sells not only equipment and components in the field of communications, but also a wide range of high-tech products in various industries. KVD cooperates with many well-known international brands mainly in OEM and ODM contracts, and its products are represented in more than 200 countries of the world.
Specifications
Technical characteristics HOMTOM HT6 (Post kalipso888 # 44448407)
Attached Image

Contents of delivery
Attached Image


Implemented fast charging technology (PumpExpress): 75 percent charged in 30 minutes. Charging 5V, 2 amps.
Release is expected in September.
Interpretation of the mark.
HOMTOM can be passed as "Heng Tong"which conveys the rich wisdom of the brand. In China, “Heng” means eternal, “Tong” means skill. HOMTOM (Heng Tong) implies continuous change and innovation to explore the path to eternal truth.
Official site-http://www.homtom.cc/p...il.php?ProId=35&Cate=3
Unpacking
Review in Russian
Useful
Size table acb.
Which processor to choose in the smartphone
Certificates and type of acb
5 practical tips on battery operation.
The exact weight of the smartphone, photo
How to enter Recover + Getting Root
We get ROOTrights, flashTHIS PATCHofTWRP Recovery
How to make simultaneously 2 sim and microSD
Video on how to make simultaneously 2 sim + microSD.
Homemade our branch at the same time 2 sim + microSD.
Calibration of the light sensor!
SIM Card Tray Replacement
Increase the volume of conversational dynamics.
Guide for replacing conversational dynamics for HomTom HT6.
Making a do-it-yourself case
Recovery tray.
HT6 disassembly
Screen translation with factory tests.
Smartphone comparison site
Increased autonomy or method of freezing "waking up" software
Libraries from the Doogee T6 R05 Camera.
A set of software
How to make an access point from a phone
Engineering menu of phones based on MTK processors
Manuals for the restoration of touchscreens
Solving the problem of installing different melodies on SIM cards and contacts
Battery Problem Solving

Ways to Calculate Energy Consumer
Please, before writing here with your problem, follow the steps below.
1. Lay out screenshots (under the spoiler) Settings - Battery (Attach screenshots here, try to figure it out together). Also detailed schedule from there too.
2. Install Wakelock Detector and find out which system process is chewing (Also post screenshots)
Attached fileReference + materials + BBS + and + wavelets.rar(40.49 KB)

3. Go to the For developers section and look at the process statistics (how to open the developers section: go to settings - about the phone, and click on the Build Number 5-8 times, then go to the settings again and find this item. Or google it like do)
4. Dial * # * # 4636 # * # *, click "Usage Statistics", see which program works as much (sort it in advance by time of use, launch, and trace it).
5. Go to settings - about phone - build number - press 8 times. Then the settings — for developers — show the CPU load. And there to see what is in the first places, and whether it is constantly.
6. Get extensive battery statisticsno need for root access for Android 5.0 and higher
General User Tips and Tips
Here is the place for the analysis of scripts, specialized software and experiments.
Do not delete, but disable (freeze) system applications.
1. Remove extra widgets from the desktop
2.Disable live wallpapers
3. Settings ->wi-fi ->additional functions ->wi-fi in sleep mode - only when powered from the network
4. Settings ->wi-fi ->additional functions ->uncheck - "always search for networks"
5.Location - disable "Sending geodata."
6.Disable not very necessary synchronization
7. Disable automatic updates and update notifications on Google Play.
8. In Google Now, leave only the search, that is, do not activate Assistance
9. Disable Push and notification of social networks. Disable push messages from the operator
10. In custom kernels, do not use the doublet / swipe function.
11. Do not use task killers.
12. Do not use monitoring programs and widgets in the daily operation of the smartphone.
13.DisableFast dormancy
14.When poor quality of the LTE network connection, switch the “Network Type” to 3G or 2G
15. Use a different browser instead of Chrome.
16.Viber(wi-fi is always on)+
Disable services - For those who are interested in what services in Android can be disabled to save battery
17. Tips for setting up the phone(photo instruction)
18.Disable unused services
19.Uninstalling Android system apps
20.Why you should not use Task Killers on Android
21.Lithium Batteries - Operating Rules
22.List of programs that can be safely removed
23. As a result of testing and observation on other devices, the accelerometer is recognized as the leader of energy consumption. To save energy, it is enough to turn off the automatic screen rotation. It is recommended to turn off auto brightness.
24.Battery calibration
25.Battery university- educational program for batteries, operation of controllers, etc. In English (
26.Wipe the battery does not affect the running time of the smartphone.
27.The device and the principle of operation of lithium-ion (Li-ion) batteries
28.Disable services.

Useful programs

BetterBatteryStats- A utility for monitoring battery discharge.(Detailed program description)
Disable Service- Enable and disable services.
Greenify- Management of background processes
My Android Tools- Disable / enable activity, service, receiver, provider for any applications
Llama - Location Profiles- Automate Android, change profiles by time and location (cell network towers).
Wakelock detector- Search for reasons for not falling asleep device.(detailed program description)
JuiceDefender- A set of tools to extend battery life.
3G Manager- Optimize the use of 3G.
GSam Battery Monitor- Utility for monitoring energy consumption.
Nova Battery Tester- Testing and determining the actual capacity of the battery of the phone or tablet.
Servicely - ServicelyAllows you to determine and put into sleep mode background processes and services that run on certain events.
Autostarts- Startup Manager. Perhaps the best program in its class
OS Monitor- system monitoring. Displays a list of processes, connection to networks, etc.
CPU Spy- Allows you to determine how long the processor is running at each of the available frequencies
LBE Security Master- Excellent combine. Control of memory, traffic, access to applications to the Internet, etc. ...

HT6 Accessories
Reviews, reviews, tests:


How to search for information in the topic.
Important! First time in the topic? Read it!
Attached Image


To avoiddevice failures ,failure andbattery bulgeIn view of overheating DO NOT use native charging


There is no curator in the subject. For questions about filling the caps, please contact the section moderators via the buttonPictureunder the messages to which you want to add links.

Post has been editedMagnifikus - 07.04.17, 05:52
Reason for editing: Solving a battery problem
Forum: HOMTOM · View message: #41844482 · Replies: 4697 · Views: 799445

kalipso888
12.03.16, 00:19
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746    +

The solution for those who after the firmware or update have problems with the touchscreen.
(description of the problem) | for the touchpad configuration model, and for digging into the goodix utilities thanksonefabis.
Most likely you installed the firmware with someone else's kernel. And you did not help the firmware with the native core.
Now your config is most likely different from the native one.
How to enable usb debugging
1. Open the Settings menu.
2. Go to the "System" section, which is located at the very bottom
3. Tap on the item "About phone"
4. Find at the bottom of the item "Build Number"
5. Click on it about 10 times, then the developer options menu will open.
6. Go to the menu to find the item debug on USb, put a tick.
And you also need to press the factory unlock!

The touch should at least somehow work to press the buttons, if there is otg support, then it's easier, you can connect a mouse.
For more convenience, you need to putAirdroidfor remote access on the smartphone and to be able to confirm the rights of the superuser in the process of action.
and ROOT rights must be obtained. Of the programs should be Busy box, Terminal.
Root
Busybox
Check Root rights!
Terminal
ˇTo work on adb and with fastboot, use the program 15 seconds ADB Installer (in the header, it will install everything and make it systemic).
V 1.4.2
V 1.3.
It is the adb program that helps to establish a connection between a computer and Android download here.
ADB and all that can be done with it (Post by lezgi_boy # 45009855)
We unpack the archive (it is recommended to unpack to the root of the disk or to another folder that does not contain Russian letters on the way,). For example: c: \ adb \ or D: \ adb \
The result should be a folder in the root of the disk with the contents:
#: \ adb \ adb.exe - directly the ADB itself, with which we will work.
#: \ adb \ AdbWinApi.dll is a library for working with ADB.
#: \ adb \ AdbWinUsbApi.dll is a library for working with ADB.
Now
1. Download and unpack the archive[attachment = "7732000: Fix_Homt ... 6_sensor.rar"]
https://yadi.sk/d/vqDkoJRcpwUDe
The archive has all the slides of your future actions, so first read.
[Attachment = "7767470: Slides in ... act_.zip"]
2. We check that the ADB drivers are installed and the USB debug is enabled.
Perform the following steps:
Start menu, in the window to find programs and files, enter CMD (Run ->cmd ->enter)
1. Start ->Run ->cmd ->Enter (Enter).
2. Key combination WIN + R ->cmd ->Enter (Enter).
We write in the black window cd c: \ adb
in response we will
c: \ adb>
further we write next to the same letters where the cursor is blinking
adb devices (it should work like this c: \ ADB>adb devices)
will turn out
List of devices attached
ZDSCW89TV8LRBIVK device (our smart is perfectly visible)
Then we write the following (you can not write and just copy and paste)
c: \ adb>adb shell ls / proc / gmnode *will get
/ proc / gmnode20160310 (for each firmware, their numbers are determined by enteringadb shell ls / proc / gmnode *
The code that you need to enter in the program GtpAdbTool.exe. The code can also be copied with the mouse in order not to enter the letters manually.
To do this, hold down the right mouse button, a window will appear and mark the item in it, press the left mouse button.
Place the cursor on what needs to be marked, the selected text will be in a white background. Select the desired one and press the right mouse button.
And that's all. Then you can already insert this code into the window in order not to write to manual insert, press CTRL + V.

Now you have configured everything to work adb mode

3.We connect the USB cable with the included smartphone and not standing on the lock, and run GtpAdbTool.exe.
To connect the Goodix ADB Tools program, you need to enter the command using the command via ADB
In the lead teamadb shell ls / proc / gmnode *to find out the data (as a secret password) running the program.
And then it will give out your gmnode xxxx file.
This is what you need to enter in the GtpAdbTool version 1.7 window that opens (since only version 1.7 supports the GT9157 chip.)
Attached fileADB ______ V1.7_20140424.rar(12.73 MB)

Attached Image

And click on the window that says determinate (do not disable). The program will start.
On the smartphone, you need to set the lock time to 30 minutes. Because If he gets to block, then the program will give errors. You must stand root for the right as when connecting Chinese programs ask for root access when connecting. Without it, there will be no communication of programs with the phone and it will not be possible to upload the config of the touch to the smartphone.
Attached ImageAttached ImageAttached Image

The smartphone should be turned on and should not stand on the lock. If you do not see the chip in the Goodix ADB Tools program,Watch the video carefully with a time interval on the timer 1min.00sek. 2 min. 22 sec. It is also necessary to watch the video very carefully.https://www.youtube.com/watch?v=XZWxQKp8TKc
because These actions in the program are very important!

5. Perform the following steps:
Where tsiferka 1 choose GT9157 (if the machine did not get out). Then there where tsiferka 2 click to highlight this item. Then press button 3 and select the downloaded config for your version of the wheelbarrow. Then click on the button under the number 4.
Attached Image

EVERYTHING! We are happy with the result.
I'm not saying that it is on this phone that these codes will work, but it's worth a try!
General engineering codes
*#*#8612#*#*(EngineerMode)
*#*#8613#*#*(Avto test, All tests)
*#*#8615#*#*(Factory mode)
What happened
Attached Image
and how it became
Attached Image

Instructions for those who have lost their IMEI, but at the same time at least once with a smartphone tied to a Google account:
1. We pass on the linkhttps://www.google.com/dashboard/?hl=en
2. Deploy Android - Devices.
3. We see the name of the smartphone model, the last activity date and IMEI for the first SIM card. Things are easy - calculate the second IMEI
4. To calculate the second IMEI, follow the link -http://www.imei.info/calcand in the field enter the first IMEI, in the field enter 14 digits, the 15th digit will be in a separate field, this field shows the checksum. That is, 14 digits in the first field + 15th digit in the second field = your first IMEI. How to calculate the second IMEI? To do this, change the 14th digit in the first field to +1. For example, if the 14th digit was 6, change it to 7. The second field will be updated, it will show the new digit. As a result, we combine 14 numbers from the first field with a number from the second field and we get the second IMEI for your phone.

Post has been editedmaxikyoy - 25.09.16, 16:05
Reason for editing: added prog!


--------------------
Do not say if it does not change the silence for the better.
Forum:Highscreen· View message:#47868531· Replies:18327· Views:3241621

kalipso888
10.02.16, 15:55
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

PurchaseHOMTOM HT3
PictureVenso Isprit U50, Ergo A500 Best Dual Sim
Description | Purchase | Discussion | Firmware



Post has been editedsergej4388 - 19.08.16, 09:29
Reason for editing: Additional names


--------------------
Do not say if it does not change the silence for the better.
Forum:Buying devices· View message:#46996425· Replies:3104· Views:113257

kalipso888
22.11.15, 19:28
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746  +

PurchaseHOMTOM HT6
PictureHOMTOM HT6, HOMTOM HT6
Description |Discussion � | Purchase�|� Official firmware
Before asking a question
Attached Image
Tracking tracks, programs.


There is no curator in the subject. For questions about filling the caps, please contact the section moderators via the buttonPictureunder the messages to which you want to add links.

Post has been editedSergey_Ace - 05.06.16, 21:52
Reason for editing: Removed link to Forum Rules from Rubricator
Forum: Buying devices · View message: #44721298 · Replies: 552 · Views: 46249

kalipso888
05.04.16, 16:00
Guru
*********
[offline]

Group: Banned
Messages 4740
Check in: 25.10.08
InFocus M2

Reputation:-  746    +

PurchaseBlackview a5
PictureBlackview a5
Discussion | Purchase | Official firmware



Specifications
Processor Brand: MediaTek Processor
Processor: 6580
Processor Type: Quad-Core
Processor frequency: 1.3 GHz
Os: Google Android 6.0
Product type: 3G phone
Memory
RAM: 1 GB
Rom: 8 GB
SIM cards: 2 SIM
Sim card type: 2 micro sim
Main display: 4.5 inches
Screen resolution: 854 × 480
Screen Type: Capacitive Screen
Multi-point touch: Support
Main camera: 5 MP
Camera sub: 2 MP
Flash: Support
Capacity: 2000 mAh
3G: Support
Wi-fi: Support
Nfc: No
Gprs: Support
Egsm: Support
Wap: Support
2 g frequency: GSM 850/900/1800/1900
3G frequency: WCDMA 900/2100
Gps: Support
Otg: No
Ota: No
FM Radio: Support
Language: Multi-language
Cable Connector: Micro USB 5Pin
Headphone jack: 3.5 mm
Size: 129.9 * 66 * 9.5mm
Accessories: 1 * USB cable, 1 * language user manual, 1 * box
Available colors: Pearl White, Violet Black, Sky Blue

Links to verified sellers


There is no curator in the subject. For questions about filling the caps, please contact the section moderators via the buttonPictureunder the messages to which you want to add links.

Post has been editedEnlightened grandfather - 02.06.16, 11:17
Reason for editing: Reduced to standard section
Forum: Buying devices · View message: #48595792 · Replies: 784 · Views: 64879

220 pagesV  1 2 3 4 5 6 > » 



 mobile version Now: 02.06.19, 05:46