Did anyone have the latest firmware from merlin for rt-n12 C1 and VP?
I would be grateful, but the links are all dead.

power burned brightly, the rest was dim.

Yesterday such a patient was, managed to sew there openwrt from E4, naturally a brick with similar symptoms. I stitched a dump from K2 and through failsafe I rolled in my native firmware, a bootloader from K2 goes to R1.

It turned out to edit the contents of the original squashfs, followed by assembly into the firmware, which is typical of the working firmware. ;)

Perhaps he also found a crutch with a reboot, vmlinux from sorts leads to a reboot with any squash contents. I cut it out of the working firmware, and the next time I will again run around the file systems from similar routers.

I launched the firmware from the DIR-615 Q2, there is little that works, the settings are not saved, the wi-fi module is 8188 there, so it does not work either.
I compiled the output upg method from the makefile, substituting sqashfs from d-link. Only for experiments, the firmware is not reversible without a programmer.
http://cloud.mail.ru/public/Me5J/DqnLZpGqa

Firmware from 04.00.05 leads to a reboot not due to the lack of scripts and interface, there is some other reason. Substitute both native and edited squashfs, the result is the same: you barely have time to go into the interface and reboot.

Dumps DIR-300-A1, one with native firmware, the second OpenWRT. I counted on every fireman, MAC 00: 26: 5a: 32: 64: 8f

https: //drive.google.c.…ok0UQGmT2FqWXpnMkNON00

This device with DDR2 memory, I suspect a global difference from the DIR-615 Q2, DIR-300A D1, etc. With the left dumps further bootloader until it goes. I'll pick more.

Squat

I think about your thoughts, how free time will be.
Can you try to collect ask from the d-link 615 Q2? I threw a link to the sortsy from the cloud, I really want to look at it and pick it up.
Still a flash dump from him to get. ;)

connect1.asp is in one of the executable ELF files, it’s not a fact that a simple change to the config will take a ride.

Post has been editedaxis259 - 07.08.16, 17:09

Squat

I took the firmware from the netgir forum, it was in the thread with jwnr2000 v4, it seemed to be laid out to me for the biline subscribers. From it, I could not unpack squashfs, by the way. She will not take her bootloader from the house apparatus, because it is not profitable for the domra, they now have programmers who do not eat bread for nothing.
There is an opinion how to sew the left squashfs to the header of our device? I made sure that the compiled update from source is accepted as a native firmware. Maybe there is a way to adjust the checksum and the size of the squash in bytes in the header?

There are sources from the firmware of the router on the same hardware, but only the sources, I did not find a single firmware, the device was not produced in the territory of the Russian Federation. DIR615 Q2. I could not compile it, the config does not see the toolchain, there was no time to figure it out. dlink recommends distribora distribution for compilation, while there is no time to follow their recommendations.https://cloud.mail.ru/public/DzUB/4V8yZGHyj

I already have experience of turning Chinese routers into Asus RT-N12E on RTL8196C. Practice clone here in my opinion the most effective.

Post has been editedaxis259 - 04.08.16, 17:47

What I found, I found it. How do you understand that does not recognize? What domra does not allow to change the firmware to any other than them?

In the operator's firmware, the entire original interface is present, by the way. Just get it as a question.
The operator interface from the web at startup goes to / var, the rest of the files are not used.

Found me firmware from netgear:
https://cloud.mail.ru/public/D5ty/wxP8nD5SD

Firmware (software update) from domra:
https://cloud.mail.ru/public/7wjS/az2URCXuQ

And in your firmware with a perpetual reboot failsafe case does not start?

There is theoretically the original firmware from netgira, just how to feed it to the router?

Yes, there was a sinful thought that something was wrong with these dumps. As a result, everything with them is so, this piece of iron does not work for me. The LEDs blink dimly.

Friends, does anyone have a fullflash 615 M1? I will thank you.