Local [offline]
Group: Friendssavagemessiahzine.com Messages 135 Check in: 26.08.07
Reputation: 59
| DiscussionNetgear AirCard AC785 (S), AC790 (S), AC810 (S)��������� LTE ������� Netgear AirCard downloadCharacteristics of the last three models of routers Netgear For Russia, relevant European versions of routers (not locked). For them in the numbering of any letters at the end of the model number is not put. Netgear AirCard AC785 Mobile Hotspot URL to the European site NetgearRouter on Qualcomm MDM9225, LTE cat.4 chipset, no aggregation, speed up to 150Mbps SKU code indicated on the box for a single European model: AC785-100EUS Supported frequencies: LTE FDD: B1, B3, B7, B8, B20 LTE TDD: B38 3G: 850/900/2100 MHz 2G: 900/1800 MHz Battery for AC875: NETGEAR W-3 Capacity: 2000 mAh (3.7V, 7.4Wh) Netgear aircardAC790Mobile Hotspot URL to the European site NetgearRouter on Qualcomm MDM9230, LTE cat.6 chipset, two lanes aggregation, speed up to 300Mbps The SKU code shown on the box for a single European model: AC790-100EUS Supported frequencies: LTE FDD: B1, B3, B7, B8, B20 LTE TDD: B38, B40 LTE CA: B3 + B20, B3 + B7, B7 + B20, B3 + B3, B7 + B7, B38 + B38 3G: 850/900/1900/2100 2G: not supported Battery for AC790: NETGEAR W-7 Capacity: 2930 mAh (3.8V, 11.8Wh) Netgear AirCard AC810 Mobile Hotspot URL to the European site NetgearThe router on the Qualcomm MDM9240 chipset, SKU code shown on the box for a single European model: AC810-100EUS On the box with the router indicated - LTE cat.9, aggregation of three lanes, speed up to 450 Mbit / s The site and datasheet indicate - LTE cat.11, aggregation of three lanes, speed up to 600Mbps Supported frequencies: LTE FDD: B1, B3, B7, B8, B20 LTE TDD: B38, B40, B41 LTE 2CA: B1 + B8, B1 + B20, B3 + B3, B3 + B7, B7 + B7, B3 + B8, B3 + B20, B3 + B38, B20 + B20, B38 + B38, B41 + B41 LTE 3CA: B3 + B3 + B7, B3 + B3 + B20, B3 + B7 + B7, B3 + B7 + B20, B40 + B40 + B40, B41 + B41 + B41 3G: 850/900/1900/2100 2G: not supported Battery for AC810: NETGEAR W-7 Capacity: 2930 mAh (3.8V, 11.8Wh) Operator versions of routers come with a letter Sat the end of the model number: Different LTE ranges for a particular operator, and usually go locked under it. For example: Netgear AirCard AC810S for the Australian operator Telstra The router on the Qualcomm MDM9240 chipset, LTE cat.11, aggregation of three lanes, speed up to 600Mbps http: //www.netgear.com...d/hotspots/AC810S.aspxSKU code: AC810S-1TLAUS LTE FDD: B1, B3, B7, B8, B28 (Australian frequencies, our B20 is not. Because of this, there is not much use in Russia) LTE TDD: not supported (our B38 is not) LTE 2CA: B3 + B28, B3 + B7, B7 + B28, B7 + B7 LTE 3CA: B28 + B3 + B7, B3 + B7 + B7, B28 + B7 + B7 3G: 850/900/1900/2100 2G: not supported Netgear AirCard AC810S for Polish Play operator Router on Qualcomm MDM9240, LTE cat.9 chipset, aggregation of three lanes, speed up to 450 Mbit / s http://www.play.pl/tel…netgear-router-ac810s/SKU code: AC810S-1P1PLS LTE FDD: B1, B3, B7, B8, B20 LTE TDD: B38, B40, B41 LTE 2CA: B1 + B8, B1 + B20, B3 + B3, B3 + B7, B7 + B7, B3 + B8, B3 + B20, B3 + B38, B20 + B20, B38 + B38, B41 + B41 LTE 3CA: B3 + B3 + B7, B3 + B3 + B20, B3 + B7 + B7, B3 + B7 + B20, B40 + B40 + B40, B41 + B41 + B41 3G: 850/900/1900/2100 2G: not supported The router is not locked to the Play operator. Any sim cards work. In terms of frequencies and characteristics, the Polish router AC810S-1P1PLS is completely analogous to the European version AC810-100EUS. Netgear AirCard AC810S for the American operator Sprint The router on the Qualcomm MDM9640 chipset, LTE cat.9, aggregation of three lanes, speed up to 450 Mbps CDMA / RTT / Ev-Do router SKU code: AC810S-1SNNAS LTE FDD: B2, B4, B5, B12, B25, B26 LTE TDD: B41 CDMA / Ev-Do: 800, 850, 1900 3G: Band II, IV, V 2G: not supported
Netgear AirCard AC815S for US AT & T operator The router on the Qualcomm MDM9240 chipset, LTE cat.9, aggregation of three (two ???) lanes, speed up to 450 Mbit / s - dust and moisture protected housing (IP65) - high-capacity battery 4340 mAh http: //www.netgear.com…/AC815S.aspx? cid = gwmngSKU code: AC815S-1A1NAS LTE FDD: B2, B4, B5, B7, B12, B30 LTE TDD: not supported LTE CA: ??? 3G: Band II, V 2G: 850, 1900 Useful information on Netgear routersAccess to the AT port of the router Four ways: 1. Through the regular driver (works on any AC78X, AC79X, AC81X)- Download port driver AC78xSDrivers.exefrom netgear site. - install the driver, after which three COMxx virtual ports will appear in the system: NETGEAR WWAN Modem VSP NETGEAR DM Port VSP NETGEAR NMEA Port VSP - connect the router with a USB cable to the computer. - knock on the virtual port "NETGEAR WWAN Modem VSP" terminalkoy. 2. Access directly to the port without installing the driver, via USB-cord through the network interface RNDISIn Netgear routers - AT, the port is also active in AT port over TCP. For use: - connect the router with a USB cable to the computer. - Use for example Putty or any other terminal and select in the settings HostName: 192.168.1.1Port: 5510ConnectionType: Telnet3. Access directly to the port via Wi-Fi connectionBy default, access to port 5510 via Wi-Fi is blocked. To bypass, you need to change the port number to another value. You can connect via Wi-Fi by analogy with the example above: HostName: 192.168.1.1Port: XXXX (which you put in the config)ConnectionType: TelnetDetails on changing the port from sandwern: Netgear AirCard AC785 (S), AC790 (S), AC810 (S) - Discussion (Post sandwern # 52346558)Attention! Standard password from Sierra "A710" - does not fit Netgear routers for unlocking extended AT commandsNetgear uses its modified passwords. And for different models - passwords are also different. For aircard AC810-100EUSblocking from extended AT commands is removed through AT! ENTERCND = "whistler"For aircard AC810S-1P1PLSblocking from extended AT commands is removed through AT! ENTERCND = "seymour"For aircard AC810S-1TLAUSblocking from extended AT commands is removed through AT! ENTERCND = "grouse"For aircard AC810S-1RDQASblocking from extended AT commands is removed through AT! ENTERCND = "cypress"For aircard AC790-100EUSblocking from extended AT commands is removed through AT! ENTERCND = "lavender"For other Aircard ACxxx - passwords are not yet known. But if you want, you can always try to find out from the router itself ... It is enough to remove the dump sections of the flash drive and pull it out from there ... Access to the diagnostic port of the router (for QPST, QXDM, etc.) Two options: 1. Through the regular driver from Netgear- Download port driver AC78xSDrivers.exefrom netgear site. - install the driver, after which three COMxx virtual ports will appear in the system: NETGEAR WWAN Modem VSP NETGEAR DM Port VSP NETGEAR NMEA Port VSP - connect the router with a USB cable to the computer. - Install QPST, and in the settings select the port "NETGEAR DM Port VSP" QPST 2.7.437 you can take hereor 2.7.441 here2. Access directly to the port without installing the driverIn the AC810 router - the diagnostic port is also active in the DM port over TCPDefault values: HostName: 192.168.1.1Port: 5511For use with QPST, we add these values in IP: PORT format on the Ports tab.>Add New Port>Outgoing IP Connections. By default, access to port 5511 is open only when the router is connected to the computer via a USB cable. If you want to get work with the Dianhous port via Wi-Fi, then you need to change the port number to another value. Details on changing the diagnostic port from sandwern: Netgear AirCard AC785 (S), AC790 (S), AC810 (S) - Discussion (Post sandwern # 52578326)Determination of carrier parameters when working in the aggregation mode (Carrier Aggregation) Actual for AC790 and AC810. Parameters of carriers that are participating in the aggregation mode (Carrier Aggregation) are not visible in the web interface of the router. It displays data only on the main carrier. You can find out the parameters of all carriers only with the help of AT commands. To see them you need: 1. Start the download and wait for the LTE-A icon to appear on the router's display. 2. send the command AT! GSTATUS? The response in the "PCC:" section will be the parameters of the main carrier. In the sections "SCC1:" and "SCC2:" for additional. example from Sandwern. Aggregation B7 (20Mhz) + B7 (20Mhz): AT! GSTATUS? ! GSTATUS: Current Time: 254 Mode: ONLINE System mode: LTE PS state: Attached EMM state: Registered Normal Service RRC state: RRC Connected IMS reg state: No Srv
PCC: LTE band: B7 LTE bw: 20 MHz LTE Rx chan: 2850 LTE Tx chan: 20850 RSSI (dBm): -73.5 RSRP (dBm): -101.5 RSRQ (dB): -7.2 RSSNR (dB): 19 Tx Power (dBm): 11.0 LTE Cell ID: 253717762 Physical Cell ID: 29 TAC: 9987
SCC1: LTE band: B7 LTE bw: 20 MHz LTE Rx chan: 3048 RSSI (dBm): -78.3 RSRP (dBm): -97.1 RSRQ (dB): -9.7 Physical Cell ID: 29
Ok Configure user profiles for AT! BAND Post has been editedSkvo - 25.03.17, 00:25 |