Q: My GU from this topic? A: If your version of MCU (settings about the device) starts with MCU: MTCE_XXX means from this.
If different - this is not your issue. Look for your theme
here Q: When I try to log in to the "Factory Settings", a password is requested. What is he like? A: 126. On rare devices - 3368, either m123456, or 121212.
Q: What is the "factory settings" and where to find them? A: This is the menu item settings - special settings - factory settings (for some this is the “boot menu”) when you switch to which you are in hidden settings. Be careful with any changes in this menu.
Q: Can I change something in the factory settings, including the last tab "Others"? A: After entering the factory menu, it is recommended to immediately save the settings image with the EXPORT button so that you can restore all settings to their original state if necessary. The image of the settings will be saved in the memory of the PG (dmcu.cfg file).
What can and cannot be changed in the Others tab described in post.
Q: How to get root-rights? Рћ: Through ADB -
hereA: Another method -
hereA: Another method -
hereQ: How do I save Forums GU firmware? ABOUT:
The answer is in the postQ: How to enter recovery mode? ABOUT:
The answer is in the postQ: How to enable the developer menu? ABOUT:
AnswerQ: What is the power consumption in sleep mode PX6? Рћ: When the red wire is disconnected, the consumption in half a minute drops to 5.7 mA.
Q: GU takes a long time to load. So it should be? A: Settings - specific settings - advanced settings - switch-off delay of the ACC. If you select "Auto Sleep" GU will be constantly on standby and will always be included in a few seconds. If you set 30 seconds - 1 hour, SU after this time will be completely switched off. It not recommended to put a permanent sleep, because in the long simple car (eg a week or more), you can put your battery fully.
AT:
How to make friends GU and ELM327? ABOUT:
The answer is in the post.AT:
How to set up the touch and train the touch buttons? ABOUT:
Q: Can I train the buttons on the steering wheel / radio to your taste? A: To learn the steering buttons, find the corresponding application in the PG. To learn the physical buttons on the GU, go to the factory settings - Key Study tab - Pannel Key Study.
If the connection of steering buttons through the CAN bus auto - learning is possible, but not all firmwares. More
hereand
instructionQ: How does the Auto Brightness function screen? ABOUT:
The answer is in the postQ: How to call, send SMS voice? ABOUT:
The answer is in the postQ: I have videos from YouTube and other sources playing without a picture (there is sound, but there is no picture - a black screen), what should I do? A: Settings - driver settings - enable playing video in motion, activate the slider.
Q: How to change the logo of the car? A: Factory Settings - Car Logo Tab
Q: Does radio, music from drives or via A2DP profile (via Bluetooth) play loud / quietly relative to each other? A: The factory settings - tab Voice - expose the sound levels on your taste. If you have Kanshin also looking
hereIn: The volume at the minimum level is too high, you can somehow make quieter? ABOUT:
The answer is in the postQ: What is the CanBus tab responsible for in the factory settings? A: If you have a cannon in the car and a kanbas decoder is included with the PG, the correct values ​​for the data exchange between the PG and the car are set in this menu.
Q: Why can't I connect an external Bluetooth keyboard, button, volume knob, etc. After all, the radio tape recorder sees the device? Рћ: The BT module of the GU is trimmed and can work ONLY with two things: 1. An OBD adapter and 2. A speakerphone for the phone.
Q: My saved stations are reset after a reboot and some application settings, what to do? Рћ: Factory settings - the others tab - the item "Default power status" set the value "Memory status of last".
If this does not work - check is not reversed if you wire ACC and B +
Р’: I do not synchronize contacts on the GU with the phone, what should I do? ABOUT:
The answer is in the postQ: How to find out the version of my Bluetooth module? A: The factory settings are the first tab, the first line. Change version is not recommended.
Q: What is the principle of the front (front) camera? ABOUT:
Answerand
connection sequenceQ: Turning on the reverse gear mutes the sound. How to fix? ABOUT:
The answer is in the postQ: I do not have a rear view camera, how can I remove the yellow triangle with an exclamation mark and a black screen? A: Factory settings - the others tab - the "prohibit reverse" item - set the value to disabled.
Q: The navigator completely cuts off any sounds at the time of work, or it works too quietly / loudly, how to decide? ABOUT
The answer is in the postР’: After turning on the GU, you have to re-enable WiFi, how to solve? Рћ: WiFi settings - automatic inclusion.
Q: How do I enable screen sharing? ABOUT:
response to fasting.It does not work on all firmware versions. List which
works