Need to warn ...
4.0.0 firmware is a completely new branch, a lot of things have been updated, right down to the kernel version.
Strictly speaking, 825ac for this firmware is rather weak with process and RAM, flash too little, so the firmware is heavily cut in terms of whistles and fakes.
Be mentally prepared for the fact that the web muzzle will slow down.
For those who are sitting on non-processor-dependent connection modes (pptp, l2tp), I do not recommend setting it, and so it’s not so easy.
From the pros - a new kernel, a new management interface for cli, up to the integration of lua scripts, a lot of things can be configured only from cli (openvpn, 6to4). but you have to understand that this is for enthusiasts who, at one time, were very busy picking up microtics in cli.

D-Link DIR-825AC - Discussion

• In the subject are allForum Rulesand10 commandments novice who is hard to master the Rules of the Forum
  
• Discussion of devices not related to this topic is prohibited. If the theme you need for a specific model does not exist - create it.
  
• Instead of saying “Thank you!” Use. If you have less than 15 posts - click on the button.under the message where they helped you, and write thanks.
  
• Useful topics to note:Forum FAQ, How to search the forum?, How to remove the image under the spoiler., Guide Networks and Equipment
  

There is no curator in the subject. For questions about filling the caps, please contact the section moderators via the "Complaint" button under the messages to which you want to add links, or through QMS.
Attention!!! If after upgrading to 3.0.4 there are strangers in wireless or speed, reset the factory settings and configure the router again.

Post has been editedstp101 - 16.04.19, 12:26

What does it have to do with a router? The advertisement shown in the pages that you watch is shown.
The router is simple, it misses what arrived in response to a request that the router does not know inside these threads.
Put adblock, let it cut advertising.

Well, you can see in the statistics of clients, filtered by Ip client. but there will be a bunch of connections, I suspect.

Posted on 03/14/2019 12:20:


There was a trend in its time, the software of the routers allowed to tint the traffic of toys and pass it through itself in the priority mode. but then the channels became wider and it became clear that this was not washed away.

It is easier to see in Windows. you download the tcpview softphone, launch it before launching the game, launch the game, switch to the softphone and look at the name of the process on which Ip it breaks.

Here in this particular case, it is better (and dearer to developers) - Russian. In any case, I met a couple of times that the items in the menu with English did not work out normally, this was corrected when switching to English.

The differences are minimal - 2 times the size of the flash memory.
On the running does not affect.

Posted on 09/03/2018 06:46:


The third symbol in the product code is the bundle. Pachkordik is more true-shorter-not put, another document was printed and tdtp .. Again, the running does not affect.

Posted on 09/03/2018 06:47:


Here exactly trigering need? at the event to open a port?
Or just port forwarding?
Outline the task, tell.

Only then do not say that the d-link is bad, okay?
Wireless settings are stored in a file. when pouring the image through the programmer, they naturally will be different.


A long time ago, they learned how to make decent firmware on realtek?

Judging by the version, the firmware is customized for the provider. Usually, providers in a TK indicate the need for protection against a change to a regular, generic firmware.

Maybe on Windows firewall or an antivirus chtonit hacks? I have a questioning for the mutant, when it is turned on, and for DC ++ and from the network storage, the torrent picks up ports for itself. Firmware usual 3.0.4.

The log, if stored on the internal flash drive, is limited to 32 kilobytes. As far as I remember, addresses of connections in it are not reflected.
Try asking your provider for details per day.

Posted 06/01/2018 07:26 AM:


Routing customize. To go to the server's VPN address via the van interface, to the rest of the Internet via the VPN interface.

on the previous version of the web interface, but, in general, it is similar.
Video

Post has been editedJ0_kER - 31.05.18, 13:38

I do not know about you, in the Russian Federation the law on consumer protection allows the consumer to make a complaint both to the representative of the manufacturer and to the seller.

Posted 05/30/2018 08:35:


No, only usb flash drive, 3-4g modem.
But you can create a client's Wi-Fi interface on the router, configure it to connect to the desired access point and use this interface as the primary or alternate wan interface. But with the connection of an external antenna will be problematic.

802.11n was developed as “something to oppose 100mb wires”. As a result, you can get 128-130mbits .. if you go deep into the forest. 180 will not be anyone, and the router is not to blame. If you need speed, you need to go to 5GHz.


The price of routers in customization projects depends a lot on what. From volumes, delivery schedules, specified depth of support and service as well. You read carefully the web interface and the box from the device, what is written there about the support and service? I'm far from Krasnoyarsk to Kiev, not in the know of all the nuances, but I heard somewhere that I had an obligation to repair the malfunctions and only after the device had been checked by the provider itself to rule out any configuration errors. Ie, yes, you need to go to Kyivstar with Kyivstterovsky router. they will then go by themselves into the long. If you still diagnose that iron is to blame.
And in the D-Link office, this router will not be taken from you, because it was not you who bought it, but Kyivstar, and it was bought on separately agreed terms.

Even if eol does not mean that errors will not be corrected. The firmware is cooked while it is in the flash drive.

3.0.0 e1 and 3.0.4 r1 are almost the same; the first digits in the name of the file are the date and time of compilation. They both contain the actual filling. Support for it does not stop.

Here is exactly one message before yours - reset to the factory ones and set your hands from scratch.

After updating to 3.0.4, you need to do a reset to the factory settings and adjust with your hands.

That's just the opposite, in Hi-Link everything plows without problems. I have not even listed 3772 in hilink mode picks up and starts to rustle.
In general, a lot depends on the composition of the modem. If the firmware on the left modem is worth trying to chop off the mass-store for microsd and the emulator for the dashboard.

it is only in summer. winter will be fine. In your area, translate time to daylight? if not, then you do not need to tick.


Automatic translation of pages is not in the browser? I do not observe this at myself.


CU3, CU4 - matching filter. behind them still stands Conder galvanic isolation. in fact, it is to unsolder, add a conder to each antenna and dilute it. But I do not advise you, because HF is a very delicate matter, there is a lot that depends even on the turn of the track. In general, it will be much easier to do much worse, but it is better to make it worse.


Post has been editedJ0_kER - 27.04.18, 07:27