Rep: (72)
TJ @ 05.24.19, 08:13*
than you can open .bin

Good day!Download the archive
We unpack in a convenient place. We throw the .bin file into the payload_input folder, double-click payload_dumper.exe. In the payload_output folder we will see the unzipped files.
"" It seems to me that I did not install any additional programs.



Rep: (72)
phpcod @ 06/02/19, 14:33*
in downloade mode

Good day! Downloade mode, is a fastboot mode. ADB determines the device? If so, what is written after the definition? Also recommendEraseSystemVendorUserData.bat, before the start of manipulation.
Generally there are masters forums, as an exampleRussian GSM forum. Regarding Nokia in this forum.
savagemessiahzine.comfor the most part, a software discussion forum.
Found moreinteresting site. Judging by this site, Nokia 6.1 (2018) will receive, at the end of this yeardroid Q.

Post has been editedfanep - 05.06.19, 17:54



Rep: (72)
Good day, Dear Members! Okirpichil phone. Restored by thisthe script.
Anyone who is engaged in firmware, I recommend to have on hand the unpacked archive at the link above.
How did the scrolling happen:
The erase command in the fastboot mode erased sections. Then sewedhere is this firmware. After the first reboot during firmware,so provided by the flasher himself, who tried to sew through OSTL will understand what it is about,- reboot downloader. The phone did not boot into the system. The screen is black. In the manager it is defined asport 9008. Provided that you stand !!! Qualcomm drivers . I stood on my joy)
As soon as I saw 9008, already a scientist what it is))), I spentboot loader recoveryand then rolled the Global version of the firmware.
Everything is good, the phone is loaded. I am glad.
.....But
Until the above throughNOSTI was stitchingGlobalkuwith a choice of region RU. And it was still sewn, I tell you.
But now, - an error occurs in English Disable the Proxy ... blah blah blah. I have not established a proxy connection. Not in browsers, not at all in the system. Changing the region to RU does not work. Installed Kaspersky protection on the connection. The message, - Disable the Proxy is gone. But the region does not change. Global remains. Also, the item Factory Unlock in the settings is not active.
......
Actually, what is all written. Does someone know how to bypass proxy protection and what can it be?
"" In the phone a couple of times erase through erase in fastboot sections up to the fact thatrestored the bootloader. Those. Traces of previous installations should not remain. The firmware itself was downloaded again, in case something is wrong with it. The effect is one. Firmware becomes. The phone is working. I get root......But The region does not change. Item Factory Unlock is not active. There is an assumption, - Make an unlock with the slot switching both the main and the critical. On both slots. But this is after work.
Beat the whole head. Any assumptions?
With respect, to all responded!
Successful firmware!

Post has been editedfanep - 23.04.19, 12:11



Rep: (72)
Good day, Dear Members!
My pitfalls, I hope, serve as a good guide for you!
So this time. I started the firmware with a low battery charge. Bottom line - Error, firmware does not become. It is worth protecting the processor not to do the firmware with a low charge. The problem is that I formatted the previous installation of the firmware. Those. The phone turned out without an axis at all. The firmware does not go. Output, - leave enabled via USB in fastboot mode until it is charged. If you can disconnectbrick!!!
Either initially, as prescribed,DO NOT BEGIN FIRMWARE IF CHARGE BELOW BELOW 50%, NEVER !!!
I hope in my case everything will be fine. Otherwise service.
Always do fullDump.
Restoring it, unlike the firmware through OSTL and NOST, can be launched at any charge level. And only then flash through OSTL or NOST.
In general, as soon as the above-mentioned programs gave an error, it is better to apply recovery via Dump.
Exception error:
Error Code: 0xc6da

Error = SE_ERR_ADB_CMD_GET_FAIL_RESULT (0xc6da)
"" Who cares what it is
Solution, translation
Try using Fastboot, which is present inside the OST LA folder. So, open a command window (or Powershell) in the OST LA folder. Then run the following command:
fastboot-android devices

It just does not pay attention.
Hard times
..................
..................
..................
A few hours later. "" 5 hours - exactly.
Disconnected from the PC and connected to the charging. All this time, the phone is in a cyclic reboot. Charging does not go. Findings, -Without an axis on board, you will not even charge it !!!Akkum not to remove. The situation is stalemate.
When connected to a PC with the volume turned up, the phone did enter fastboot mode. Determined the Android device in the task manager. The inscription Download Mode, however, did not appear. Black screen with a dead battery. Applied Dump recovery. Dump has passed. After it turned out to enter TWRP in the standard way. And turn off the phone from it. In the section Reeboot chose Off. I put it on charge. Pleases at least the fact that the phone does not rebuy. The charging process is underway. The night stood on the charge of Xperia. What does charging Xperia current performance above. Now stands on its own. Maybe charging is needed only native)))) I do not know, but after the manipulations above, it charges. Not rebuilt.
In 2 words.
To go charging you need to turn off. In constant reboot, charging does not go. It was not possible to turn off the power button. Restored Dump. Boot into TWRP and turn off the phone from it.
..................
..................
..................
A couple of hours later.
Stitched through NOST. The phone came to life. All is well.
...But. I chose the RU location as before, but it became a global. What is the reason I will understand in the evening.

Let me remind you again. Dear forum, before flashing the phone. Once unlocked the bootloader. Got Root.
Did a Dump !!! For in many cases it is simply necessary. The above is such a case!
Successful firmware!

Post has been editedfanep - 22.04.19, 15:10



Rep: (72)
Good day, Dear Members! For all who intend to install / rearrange the firmware !!! Unlocked the bootloader.Installed the firmware.
If you do not know how to install factory firmware,I DO NOT ADVISE TO TAKING FOR THE FIRMWARE AT ALL !!!
Install Root. Download any file manager with Root access. Passed on the waydev / block / platform / soc / c0c4000.sdhci / by-name, put a tick on everything that is there. Exclude files ending in _b. And userdata. ... Files _b are secondary system files. Userdata files are user data. Essentially what you did in the system ...
Further
Copied the selected memory phone. Transferred from phone to PC. And store as long as the phone lives. In the copied file will be not only the firmware files, but also factory data. Such as IMEI, Serial number ... Individual data for each phone. Those. All those files that simply can not be restored with firmware. In case of unsuccessful firmware. Having returned files to your phone, you can always revive the device.
Individual data of your phone will not be in any firmware.Please understand and understand what is said.
My respects to all!
Successful firmware!

Post has been editedfanep - 22.04.19, 14:03



Rep: (72)
Good day, Dear Members! I present to your attention. Manual to restore the bootloader. In other words, Kirpich! Taken fromXDA
Manual
1.
make sure you installed all drivers from NTool drivers folder
2.
unpack P2C_BootFix.zip into some folder, go to this folder
3.
disassemble phone (preheat display or you will surely damage it)
4.
connect marked testpoint to 3.3v source, battery "+" connector will do job just fine
5.
connect phone to PC, if you do it, then you will see "Qualcomm HS-USB QDLoader 9008"
6.
immediately run load_fh.cmd and check if loader uploaded
7.
run load_boot.cmd
8.
your phone is ready to be flashed with any firmware you want
Russian:
1.
make sure you install all the drivers from the Intel drivers folder
2.
unpack P2C_BootFix.zip to some folder, for example c: \ bootfix, open a command prompt and go to this folder
3.
disassemble the phone (heat the display or you will damage it)
4.
Connect the labeled test point to the source + 3.3 V, the battery connector "+" do the job just fine
5.
Connect the phone to the PC, if you do a good job, then you will see the port "Qualcomm HS-USB QDLoader 9008", and not the ADB Fastboot Port
6.
Immediately start load_fh.cmd and check if the bootloader is loaded normally, if not, disconnect the cable, reconnect the battery and go from p.4
7.
run load_boot.UMP
8.
your phone is ready to flash with any firmware you want
Tespoint
Attached Image

All in one archive
Attached filebootfix.zip(4.73 MB)

With respect! Successful firmware!

Post has been editedfanep - 19.04.19, 23:31



Rep: (72)
lis266 @ 04/19/19, 18:38*
will something change?

Good day! Get access to the file system of the phone as an administrator. What is a bootloader, -Here's a read!
In the same place, by reference, read about unlocking.
Specifically on the topicNokia 6.1 (2018)

Post has been editedfanep - 19.04.19, 19:14



Rep: (72)
To wipe first, and then firmware

Absolutely agree.
zdorovtsev70 @ 04/13/19, 20:38*
Then did Wipe Data, Cache, System, Internal Storage
I threw the firmware and installed the gapps ..

Where to throw? On a bare phone? Again, you just throw on the included phone. And, as soon as the phone is loaded, your wipe up to one place. The system again pulled all the trash.
Council, from personal experience, get a flash drive.

TWRP, - the flash drive reads normally, without cracks and on the 9th droid. Only the phone's memory is encrypted.

Post has been editedfanep - 16.04.19, 17:15



Rep: (72)
Good day!Made custom runoff.
Dear Members! Welcomein the new branch of our phone!
Successful firmware!

Post has been editedfanep - 13.04.19, 03:34



Rep: (72)
* madnjpn
Not!AEX will be in active slot. In the other there will be pieces of the previous installations.I recommend reading
And in this case, erase 2 sections so that the new axis does not intersect with the old one.
Really a lot of questions.
Think hard before any manipulation.
This phone can be trash.
In full trash. Just throw it away. No programmers will not raise. The protection is removed, which distributes the currents to the boards and burns out all the boards against overvoltage.
EVERYTHING!!!
The word Firmware means stock firmware and only it!
Everything else is a different Axis. Different from the factory in general from the word ALL!
All the same, that on a PC put Windows and, sayXp... Linux, clearer, perhaps.

Post has been editedfanep - 11.04.19, 16:44



Rep: (72)
* madnjpn
Honestly, I do not understand what I mean. Before the firmware, they made erase sections. Ask for an official. Everything. You have a clean stock. They were picking the phone. Something does not like, repeat the procedure.
Before the firmware, they made erase sections. Ask for an official. And poking on. I do like this. How are you doing and why I do not know. I make system changes that are best checked on clean firmware.
An example of such changes. Made without the use of third-party resources
Attached ImageAttached ImageMade by turning on the hidden activations of the stock firmware.Nothing corresponded !!!
For what you need firmware, I do not know.
And, for fun, I do not recommend flashing.
Successful firmware!

Post has been editedfanep - 11.04.19, 16:03



Rep: (72)
* madnjpn If correct, then this command is nothing but a Wipe for the currently active slot.

Post has been editedfanep - 11.04.19, 15:37



Rep: (72)
* madnjpn
Good day! This erasing sections, in order to make them without tails from previous installations. Sew one section, but boot will spread them on A / B. And whatever it is, better not pick. Over this, I mean the firmware, the whole team is working. And not at the same time. Many parts of the firmware, pieces, so to speak, are taken from some other firmware and are connected by symlinks. I think the one who really thinks, just stupidly do not have time to sit on such forums. Because the seat takes a lot of good time.
Based on the above, written manuals are far from perfect. And if found doubtful, application at your own peril and risk comes down to going to the service.
Never do the things you don’t know! Read at least a little theory. Do not learn and understand, but at leastread!!!
Successful firmware!

Post has been editedfanep - 11.04.19, 15:34



Rep: (72)
* Jekill ^^ Good day! This is very good news. Maybe even install)
Internally, is there a service firmware for the 9th droid? Not update, but for OST. The device has long been out of hand, so I forgot where to look for.

Post has been editedfanep - 10.04.19, 11:43



Rep: (72)
* Djoni K., Good day! What is your model, in letters? If it's not difficult, write down the update instruction via VPN.
Djoni K. @ 04/10/19, 08:25 *
updated via VPN

I, for example, do not know how. Again, it is interesting to communicate more substantively, mentioned the VPN, wrote the instructions. Not every forumchanin can find manuals himself.
Most likely talking aboutby thisPretty poor instruction. It is not clear what was done. What phone, what version of droid? Network test, again. Since
Djoni K. @ 04/09/19, 20:44*
checked for you
Most likely the version of the radio module is not for Russia in general. You tested the line recording. For you it is important. But think about those who use the manual. Record is far from a prior for the phone. And rather, the continuation of your post sounds like this - you get the opportunity to record, but lose the stable operation of the network. What will entail the godless zher battery and constant hangs.

Post has been editedfanep - 10.04.19, 10:49



Rep: (72)
* HC_4th gen,
I would make a start from this.
And I would stop at 6.1. What he did.



Rep: (72)
zdorovtsev70 @ 04/09/19, 10:11*
b1, the cap is B2

If so, please
what is it about? Links?
zdorovtsev70 @ 04/09/19, 10:11*
at 2

If this
That in the first lines:
fanep @ 12/06/18 10:30*
Instructions on firmware.
Your bootloader is unlocked.
And this is the 8th droid.
zdorovtsev70 @ 04/09/19, 10:11*
in 1

If this
That is the 9th droid. And there already depending on the firmware.

Post has been editedfanep - 09.04.19, 17:22



Rep: (72)
zdorovtsev70 @ 04/09/19, 14:34*
will remain

Just saving previous installations in 99% of cases as a result of incorrect system operation!
I would even recommend that after each firmware in fastboot mode, make a hardcast with the command
fastboot -w
Actually, I do.
Successful firmware!

Post has been editedfanep - 09.04.19, 15:09



Rep: (72)
* HC_4th gen,
Why invent? Today did it!
All the same 5 American rubles
Attached Image

What does the answer came in a couple of hours. Pay to pay. Work very wellguys +++

Post has been editedfanep - 09.04.19, 14:37



Rep: (72)
* zdorovtsev70,
Good day! Not for the sake of advantages, firstly!
Somewhere I wrote about the raw 9th droid. I have a second Xperia XA2 device, and so the stock of the 9th droid, by the manufacturer, has already been released to it twice. And twice people have bricks.
Watch the video from the post
Good advice, - Unlock the bootloader. You at the same time rolled back to the 8th droid. And be on it.
Some lyrics:
Fanep @ 04/05/19, 23:31*
Make the maker a super axis, with super options. What to do tomorrow? What to earn?

Successful firmware!

Post has been editedfanep - 09.04.19, 10:30

Full version

Help     rules

Now: 07/24/19, 03:38